WattMaster WCC III part 16 - Manual (Page 6)

WCC III Technical Guide 15-4
15. SAT 3C/D/F INSTALLATION
Typical WCC III Installation
The SAT 3C controller is used to interface to dedicated Roof Top controller units (RTU-17 type controllers) and other
more specialized controllers (GPC type devices). Each one of the SAT 3C controllers takes up 8 Satellite addresses and
then can communicate with up to 8 special dedicated controllers. Electrically, this SAT 3C device only takes up "ONE"
satellite load. There may be up to 60 satellite loads per WCC3 satellite communications loop. An optional additional
WCC3 M-COMM loop EXP board is available that will provide an additional two WCC3 satellite communications
loops if needed.
The SAT 3P controller is used to measure up to 8 dry contact closures from up to 8 pulse meters, such as a Emon-Dmon
KWH meters. (Please note: Each SAT III controller can also interface to a single dry contact closure from a single pulse
meter on A1 input.) This SAT 3P controller is a stripped down SAT III controller with only 8 pulse type inputs. Besides
logging abilities, there are not any other functioning satellite features in this SAT 3P controller. Each one of the SAT 3P
controllers takes up 8 Satellite addresses. Electrically, this SAT 3P device only takes up "ONE" satellite load. There may
be up to 60 satellite loads per WCC3 satellite communications loop. An optional additional WCC3 M-COMM loop
EXP board is available that will provide an additional two WCC3 satellite communications loops if needed.
The WCC II to WCC III global bridge is a device that allows for data from the "old" WCC II system to be shared with a
"new" WCC III system. It was designed as a temporary solution while the WCC II system was being changed over to a
WCC III system. Electrically, this WCC II to WCC III Global Bridge device only takes up "ONE" satellite load. There
may be up to 60 satellite loads per WCC3 satellite communications loop. An optional additional WCC3 M-COMM
loop EXP board is available that will provide an additional two WCC3 satellite communications loops if needed.
The high speed cable \DSL modem is used to connect the WCC III - MCD to the internet. Alternate connections to the
internet, or even the building intranet is possible, but they will require additional IT support at the contractor level.
Typical WCC III System Installation - Multiple buildings with fiber optics connecting the two buildings. Also
shown with the use of Power and Switchable comm boards.
OE210
TYPICAL
SPACE
SENSOR
(X8 MAX)
ON/OFF RELAY
PUMPS, LIGHTS,
ETC.
8 7 SAT ADDRESS 2
1 4 8 WattMaster Controls Inc.
BINARY
INPUTS
BINARY INPUTS
L8
ON OFF 128 32
16 64
L4
L3
L2
L1 L6
L5 L7
L11 L12
ON OFF
L10
L9
ON OFF L15 L16 L14
L13
C H
4 3
5
6
2 1
LOCAL SET
STATUS 2 STATUS 3
STATUS 1
HSS XMIT LOCAL SET LOCAL SET DISABLE
BATT ON/ OFF
PULSE INPUT OPTION 1 TEST
OPTION 3
OPTION 2 ON OFF STATUS
HSS REC SAT XMIT SAT REC
ANALOG INPUT JUMPER SELECTION
CURRENT
INPUT
THERMISTOR
INPUT
0 TO 10V
INPUT
0 TO 5V
INPUT
0 TO 1V
INPUT
PROGRAMMABLE CONTROLLER SAT III
H
C
COM
CHANNEL 2 1 3 4
2 1 3 4
5 6 7 8
5 6 7 8
V OUT
GND
L
O
A
D
+V
ATI
8 7 SAT ADDRESS 2
1 4 8 WattMaster Controls Inc.
BINARY
INPUTS
BINARY INPUTS
L8
ON OFF 128 32
16 64
L4
L3
L2
L1 L6
L5 L7
L11 L12
ON OFF
L10
L9
ON OFF L15 L16 L14
L13
C H
4 3
5
6
2 1
LOCAL SET
STATUS 2 STATUS 3
STATUS 1
HSS XMIT LOCAL SET LOCAL SET DISABLE
BATT ON/ OFF
PULSE INPUT OPTION 1 TEST
OPTION 3
OPTION 2 ON OFF STATUS
HSS REC SAT XMIT SAT REC
ANALOG INPUT JUMPER SELECTION
CURRENT
INPUT
THERMISTOR
INPUT
0 TO 10V
INPUT
0 TO 5V
INPUT
0 TO 1V
INPUT
PROGRAMMABLE CONTROLLER SAT III
H
C
COM
CHANNEL 2 1 3 4
2 1 3 4
5 6 7 8
5 6 7 8
V OUT
GND
L
O
A
D
+V
ATI
"D" MODE "C" MODE
"C" MODE ADDRESSING NOTES
"C" MODE SAT III ADDRESSING STARTS
AT ADDRESS 8. EACH "C" MODE SAT III TAKES UP
8 SAT III LOGICAL ADDRESSES. A "C" MODE SATIII CAN COMMUNICATE
WITH 8 DEVICES TOTAL. "D" MODE ADDRESSING NOTES
"D" MODE SAT III ADDRESSING STARTS AT ADDRESS 4.
EACH "D" MODE SAT III TAKES UP 4 SAT III LOGICAL ADDRESSES.
A "D" MODE SAT III CAN COMMUNICATE WITH 32 DEVICES TOTAL.
SAT IIICD Communications Interface TUC XMIT
ON OFF
ON OFF
SAT ADDRESS 1
STATUS LOCAL SET
16 4
2 8 64
32 128
LOCAL SET DISABLE OPTION 2 LOCAL SET OPTION 1 TEST
BATT ON/ OFF
TUC REC SAT XMIT SAT REC
OE320
TUC-2R
OE331
TUC-5R+
W
A
R
M
E
R
C
O
O
L
E
R OVR
OE213
TYPICAL
SPACE
SENSOR
OE421- SAT III
CONTROLLER
OE454/O 455/OE456 E
SAT 3C/D/F
CONTROLLER
W
A
R
M
E
R
C
O
O
L
E
R OVR
OE213
TYPICAL
SPACE
SENSOR
WCC II TO WCC III
GLOBAL BRIDGE
WCC III-MCD
SINGLE PULSE
INPUT FROM
POWER METER
UP TO 32 TOTAL
FAN COIL, HEAT PUMP
PD VAV TERMINAL UNITS
PI VAV TERMINAL UNITS
PARALLEL FAN BOX, ETC.
VAV BOX
16 OUTPUTS
PER SAT III
UP TO 60 TOTAL SAT III
OR SAT 3C/D/F/P PER LOOP.
THERE ARE 4 POSSIBLE
SAT III RS485
COMMUNICATIONS LOOPS
(UP TO 239 SAT III MAXIMUM)
TO THE ISP
(INTERNET SERVICE PROVIDER)
CONNECTION TO THE INTERNET
(BY OTHERS)
HIGH SPEED CABLE
MODEM / ROUTER
ETHERNET
CABLE
Optional V-OUT Board
( 8 RELAY OUTS)
(2 PER SAT III)
Optional B-INPUT Board
( 8 BINARY INPUTS)
(2 PER SAT III)
HSS PORT HEAT PUMP
SAT II
SAT III
PROGRAM SOCKET
ADDRESS
24C128
PCF8583
LT1785
WATTMASTER CONTROLS INC CONNECTION
TO OLD WCC II
MANCHESTER
COMM LOOP
1 2
4
8 16
32
64 128
ADDRESS
SATIII-P
TEST LOCAL
L DIS OPT 1
OPT 2
OPT 3
R T 24 VAC GND
OPTIONS
PULSE INPUTS
“P” MODE ADDRESSING NOTES SAT III ADDRESSING STARTSAT ADDRESS NUMBER 8. EACH "P" MODE SAT III TAKES UP (8) SAT III LOGICAL ADDRESSES. THERE ARE ONLY (8) USED ACTIVE INPUTS PER SAT 3P. ANALOG INPUT #1 (PULSE INPUT #1) ON EACH SAT III ADDRESS IS ACTIVE. ALL OTHER INPUTS AND OUTPUTS ON THE SAT 3P ARE NOT FUNCTIONAL.
TOTAL WIRING FOR EACH INPUT NOT TO EXCEED 100 FEET. USE 18 GAUGE TWISTED PAIR WITH SHIELD FOR EACH PULSE METER CONNECTION. CONNECT THE SHIELD WIRE TO GND. HSS PORT
MULTIPLE PULSE
INPUTS FROM
POWER METERS
OE455-P
SAT 3P
CONTROLLER
PL102224
POWER AND
SWITCHABLE COMM
USUALLY ONE
OR TWO PER
FLOOR
SAT COMM LOOP
SAT COMM LOOP
SAT COMM LOOP
TUC COMM LOOP
B B
PL102224
POWER AND
SWITCHABLE COMM
USUALLY ONE
OR TWO PER
FLOOR
FIBER OPTIC LINES
MAXIMUM OF 2.5 MILES
(USES "ST" CONNECTORS)
BUILDING # 2
8 7 SAT ADDRESS 2
1 4 8 WattMaster Controls Inc.
BINARY
INPUTS
BINARY
INPUTS
L8
ON OFF 128 32
16 64
L4
L3
L2
L1 L6
L5 L7
L11 L12
ON OFF
L10
L9
ON OFF L15 L16 L14
L13
C H
4 3
5
6
2 1
LOCAL SET
STATUS 2 STATUS 3
STATUS 1
HSS XMIT LOCAL SET LOCAL SET DISABLE
BATT ON/ OFF
PULSE INPUT OPTION 1 TEST
OPTION 3
OPTION 2 ON OFF STATUS
HSS REC SAT XMIT SAT REC
ANALOG INPUT JUMPER SELECTION
CURRENT
INPUT
THERMISTOR
INPUT
0 TO 10V
INPUT 0 TO 5V
INPUT
0 TO 1V
INPUT
PROGRAMMABLE CONTROLLER SAT III
H
C
COM
CHANNEL 2 1 3 4
2 1 3 4
5 6 7 8
5 6 7 8
V OUT
GND
L
O
A
D
+V ATI
OE421- SAT III
CONTROLLER
8 7 SAT ADDRESS 2
1 4 8 WattMaster Controls Inc.
BINARY
INPUTS
BINARY
INPUTS
L8
ON OFF 128 32
16 64
L4
L3
L2
L1 L6
L5 L7
L11 L12
ON OFF
L10
L9
ON OFF L15 L16 L14
L13
C H
4 3
5
6
2 1
LOCAL SET
STATUS 2 STATUS 3
STATUS 1
HSS XMIT LOCAL SET LOCAL SET DISABLE
BATT ON/ OFF
PULSE INPUT OPTION 1 TEST
OPTION 3
OPTION 2 ON OFF STATUS
HSS REC SAT XMIT SAT REC
ANALOG INPUT JUMPER SELECTION
CURRENT
INPUT
THERMISTOR
INPUT
0 TO 10V
INPUT 0 TO 5V
INPUT
0 TO 1V
INPUT
PROGRAMMABLE CONTROLLER SAT III
H
C
COM
CHANNEL 2 1 3 4
2 1 3 4
5 6 7 8
5 6 7 8
V OUT
GND
L
O
A
D
+V ATI
OE421- SAT III
CONTROLLER
"D" MODE "C" MODE
"C" MODE ADDRESSING NOTES
"C" MODE SAT III ADDRESSING STARTS AT ADDRESS 8.
EACH "C" MODE SAT III TAKES UP 8 SAT III LOGICAL ADDRESSES.
A "C" MODE SATIII CAN COMMUNICATE WITH 8 DEVICES TOTAL. "D" MODE ADDRESSING NOTES
"D" MODE SAT III ADDRESSING STARTS
AT ADDRESS 4. EACH "D" MODE SAT III TAKES UP 4
SAT III LOGICAL ADDRESSES. A "D" MODE SAT III CAN COMMUNICATE
WITH 32 DEVICES TOTAL.
SAT IIICD Communications Interface
TUC XMIT
ON OFF
ON OFF
SAT ADDRESS 1
STATUS LOCAL SET
16 4
2 8 64
32 128
LOCAL SET DISABLE OPTION 2 LOCAL SET OPTION 1 TEST
BATT ON/ OFF
TUC REC SAT XMIT SAT REC
OE320
TUC-2R
W
A
R
M
E
R
C
O
O
L
E
R OVR
OE213
TYPICAL
SPACE
SENSOR
OE455
SAT 3D
CONTROLLER
VAV BOX
PL102335
RS-485 TO FIBER
OPTIC ADAPTER
USED IN MULTIPLES
OF TWO
PL102335
RS-485 TO FIBER
OPTIC ADAPTER
SAT COMM LOOP
SAT COMM LOOP
SAT COMM LOOP
UP TO 32 TOTAL
FAN COIL, HEAT PUMP
PD VAV TERMINAL UNITS
PI VAV TERMINAL UNITS
PARALLEL FAN BOX, ETC.
TUC COMM LOOP
OPTION 4
OPTION 3
OPTION 4
OPTION 3