Laney CX12-A - Manual (Page 10)

CX12-A CX15-A Cxsub-A Cxsub
Supply Voltage 230V @ 50/60Hz 230V @ 50/60Hz 230V @ 50/60Hz na
(factory selected) or 120V @ 50/60Hz or 120V @ 50/60Hz or 120V @ 50/60Hz na
Power Consumption 330W 600W 600W na
Amplifier Power rating rms 165W / 4 ohms 300W / 4 ohms 300W / 4 ohms na
110W / 8ohms 170W / 8 ohms 170W / 8 ohms na
Speaker power (r.m.s./Program) 200W/400W 250W/500W 250W/500W 250W/500W
Impedance 8 8 8 8
Frequency Range 60Hz - 18KHz 50Hz - 18KHz 35Hz - 170Hz 35Hz - 800Hz
Size W*D*H 410*330*620 500*360*700 580 * 505 * 510 580 * 505 * 510
Pole stand fitting 35mm diameter 35mm diameter 35mm diameter 35mm diameter
Shipping Weight 24Kg 19.5Kg 34Kg 29Kg
Net weight 20Kg 16Kg 30Kg 25Kg
Line gain (max) +42dBu +42dBu -7dBu to +10dBu na
Mic gain (max) +72dbu +72dbu na na
CD gain (max) +32dBu +32dBu na na
EQ Bass ±12dB @ 35Hz Bass ±12dB @ 35Hz na na
Mid ±10dB @ 2.5KHz Mid ±10dB @ 2.5KHz na na
Treble ±10dB @10KHz Treble ±10dB @10KHz na na
Crossover frequency Switchable Hi Pass Switchable Hi Pass Fixed Lo Pass na
-6dB @ 170Hz -6dB @ 170Hz -6dB @ 170Hz
12dB octave 12dB octave 12dB octave
Phase switch no no yes no
extension Loudspeaker socket yes , for 8 ohm cabinet yes , for 8 ohm cabinet yes , for 8 ohm cabinet link out
Line Out Yes , full range,0dBu nom. Yes , full range,0dBu nom. no na
peak led Indicates onset of clipping Indicates onset of clipping Indicates onset of clipping na
Cxsub recommended cross over frequency 150Hz - 250Hz
Maximum Pole stand length should be 1 meter otherwise additional support is required
Laney
10
www.laney.co.uk
Technical Specifications
.General Notes
Amplifier connection. In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off
your sound system.
With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE
turning on your power amplifier. Many products have large transient surges at turn on and off which can cause damage to
your speakers.
By turning on your power amplifier LAST and making sure its level control are set to minimum any transients from other
equipment will not reach your loudspeakers.
Wait until all system parts have stabilised usually a couple of seconds.
Similarly when turning off your system always turn down the level controls on your power amplifier and then turn off its
power before turning off other equipment.
Cables- never use shielded or microphone cable for any speaker connections as this will not be substantial enough to
handle the amplifier load and could cause damage to your complete system.
Rigging or suspended mounting. The rigging or suspended mounting of these speakers can expose members of the
public to serious health risks or even death. Under no circumstances attempt to rig, suspend or otherwise mount
this system unless you are fully qualified and certified to do so by relevant local, state and national
authorities. All relevant safety regulations must be followed. If you are not properly qualified or do not know
of pertinent regulations, consult qualified personnel for advice and assistance.
When mounted on a propriety tripod pole stand ensure the system is fully stable and can not fall over. We do not
recommend poles stands to be used higher than1 metres, without extra support.
Caution: These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with
placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.
Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.