Eureka N!ergy 9 User Manual

Your tent is now ready

Advertising
background image

REV B 4.09

fig 17

green

blue

fig 16

Component List:

1 Wired Tent Body, 2 Tent Poles, 1 Tent Fly, 2 Fly Poles, 1 Stake Bag w/Stakes,

1 Pole Bag, 4 Guy Ropes and 1 Carry Bag,

Your tent is now ready.

NOTE:

• Although it is possible to pitch this tent alone, it is faster/easier with two people.

• Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to get the

tent out. These actions may cut the shockcord and/or damage the pole ends.

• The N!ergy series tents are pre-wired with three 12V outlets. Take care to keep them in

their sleeves and avoid stepping on the sockets and wires during assembly.

3. Place a corner pin into the end of one of the poles.

At the opposite end, with the pole in one hand and a

pin & ring in the other, feed the pole up, bending it

evenly along its length to create an arc. Place the pin

into the end of the pole to maintain tension. Repeat

with the other pole. See fig 3 & 4.

fig 1

fig 2

Fly

Poles

Tent

Poles

fig 4

fig 5

fig 11

fig 15

fig 10

fig 6

fig 7

fig 8

4. Raise up the tent poles. Step inside the tent door and attach the peak

of the tent to the center of the top pole with the web clip. Attach the

remaining roof clips. See fig 5.

5. Attach the side clips to the poles to create a freestanding tent.

Place it in the desired location. See fig 6.

6. Stake the tent down through the corner web loops. Stake

opposite corners while applying tension to smooth the floor

wrinkles, squaring the tent as you work.

Also, stake out the floor

beckets at the center of each side and at the back of the tent.

See fig 7 & 8.

1. Unroll and unfold the tent on the ground. Separate the rest of the components and

place to one side. Open the door before pitching the tent. Do not stake the tent down

(however, in windy conditions, stake down one corner that faces into the wind). See fig 1.

2. Assemble the shockcorded poles.

Keep the end sections from snapping

together, as this can damage the

ends. Make certain each plain end has

been properly seated into the metal

ferrule. See fig 2.

8. Attach the fly to the tent.

Turn the fly assembly over and align it so that the poles point out

over the doors. Grasp the corners of the of the fly and drag them up and over the roof to

completely cover the tent. (This is much easier with two people.)

At the corners of the tent, reach under the fly and attach the hook & loop straps to the tent

poles, securing the fly in place. See fig 12.

At the bottom/corners of the tent, attach

the shockcorded J-hooks to the

rings on the corner webs. See

fig 13.

At the bottom/sides of the fly,

pull out and stake down the

web loops.

9. Tie a guy rope to each

of the 4 rings

attached to the fly

and stake out.

Adjust tension

with the in-line sliders.

See fig 14 & 15.

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to

power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16.

E! Power Port: Open zipper and run extension cord through opening.

Close zipper so that it rests next to the extension cord. Make sure

the zipper cover is not twisted or tucked. The cover must lay flat

against the outside of the tent to keep out rain.

Accessories: E! Power Fan/Light, E! Power Reading Light and an

E! Power 12v Adapter Cord.

Sweep Out: Inside, at the bottom of the door is a sewn-in web loop.

Pull this loop to the outside and stake it down to provide a ready exit

for floor sweepings. See fig 17.

Take Down: Pull up all stakes. Release the fly’s hook & loop straps. Remove fly.

Remove fly poles. Remove clips from tent poles and pull poles off of the pins.

Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it

on tent. Roll up both towards the open door and stow.

Read the important safety instructions on the reverse side.

fig 3

7. Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front

of the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to

side down the center of the fly forming an X. Secure the fly to the poles by wrapping the

hook & loop fastener around the fly poles. See fig 9, 10 and 11.

fig 9

fig 12

fig 13

fig 14

Assembly Instructions
for the N!ergy 9 Tent

Advertising
Table of contents