Sealey SMC01 User Manual
Page 2
Wash immediately with soap and water if battery acid
contacts skin or clothing. if acid enters eye, flush eye
immediately with cool, clean running water for at least
15 minutes and seek immediate medical attention.
remove personal metallic items such as rings,
bracelets, necklaces and watches. A lead acid
battery can produce a short-circuit current high enough
to weld a ring or similar to metal, which would cause
severe burns.
Ensure hands and clothing are clear of fan blades,
belts and other moving or hot parts of engine.
remove ties and contain long hair.
do not smoke or allow a spark or flame in the vicinity
of battery or engine.
clean the charger clamps and battery terminals to
remove any oxidation.
Ensure the correct clamp polarity is observed when
connecting to the battery.
positive is indicated by (+)
and is red,
negative is indicated by (-) and is black.
do not pull or carry the charger by its power supply
lead. Products must not be pulled or carried by their
output cables.
do not pull power plugs from sockets by the power
cable.
do not attempt to charge a non-rechargeable battery.
do not use the charger for any purpose other than
that for which it is designed.
do not allow the charger terminal clamps to touch
each
other when the power is on. remember that
gases are produced which may ignite if sparks occur.
do not place the charger inside the vehicle.
remove the battery to a safe distance for charging.
do not get the charger wet or use in damp or wet
locations or areas where there is condensation.
do not operate the charger if damaged.
do not attempt to modify or open the charger.
do not charge the battery with the engine running.
do not charge a frozen battery.
When not in use unplug from the mains power supply
and store in a safe, dry, childproof area.
do not allow untrained persons to operate the charger.
this appliance is not intended for use by persons
with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have
been given instruction concerning the use of the
appliance and are supervised by a person responsible
for their safety.
Keep children and unauthorised persons away from the
working area. children must not use the charger and should
be constantly supervised to ensure they do not play with the
charger.
WARNING! Be vigilant and cautious during the
operation of battery charging as the electrolyte is
highly corrosive and any gases emitted are explosive.
DANGER! BE AWARE, LEAD ACID, GEL, AGM,
VRLA, AND LIQUID ELECTROLYTE BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL
BATTERY OPERATION. FOR THIS REASON, IT IS
VERY IMPORTANT TO READ AND FOLLOW THESE
INSTRUCTIONS CAREFULLY, EACH TIME YOU
USE THE CHARGER.
Follow these instructions and those published by the
battery and vehicle manufacturers and the manufacturer
of any equipment you intend to use in the vicinity of
the battery. Remember to review warning marks on all
products and on engines.
1.3
personal precautions
Ensure there is another person within hearing range
of your voice, or close enough to come to your aid,
should a problem arise when working near a lead acid
battery.
Wear safety eye protection and protective clothing.
Avoid touching eyes while working near battery.
Have fresh water and soap nearby in case battery acid
contacts skin, clothing or eyes.
2. introduction
fully automatic 3-cycle switch mode charger and
maintainer designed for charging a variety of batteries: sLA,
WEt, AGM and VrLA. You know exactly how the charger is
performing; the LED’s display indicates power on charging
phase and full. charger will recover slightly sulphated batteries
and may rescue drained batteries. supplied with multi-fit
charger cables featuring crocodile clips, eyelets, vehicle
accessory plug and hard-wired terminals incorporating a water
tight plug and socket for permanent installation. for
motorcycles and cars. Plug in, connect to the battery and the
charger does the rest.
3. connection to battery
specification
MoDEL no:
sMc01.V2
input Voltage:
230V
output Voltage:
12V
charging current
2A
input current
0.32A
Efficiency
>80%
type
3-cycle
Back current Drain
<1Ah/month
Ambient temperature
-20°c to +50°c
Housing Protection
iP44
Dimensions (LxWxH)
198 x 82 x 40.5
Weight:
0.44kg
note: tHE cHArGEr sHouLD BE connEctED to
tHE BAttErY or tHE VEHicLE AccEssorY socKEt,
before connEctinG to tHE MAins suPPLY.
3.1 the output cable from the charger terminates in a socket
into which three alternative leads can be connected. (see
fig.1)
3.1.1 one lead set (A) has two colour coded battery clamps which
can be quickly attached to and detached from the battery
posts. the other end of the cable terminates with a
plug for connection to the charger lead socket.
3.1.2 the second lead (B) can be connected to the vehicle via
the vehicle accessory socket. the other end of the cable
terminates with a plug for connection to the charger lead
socket.
3.1.3 the third lead (c) is for semi permanent connection to the
battery via eyelets.the other end of the cable terminates
with a plug for connection to the charger lead socket.
Original Language Version
© Jack sealey Limited
sMc01.V2 issue: 1 - 31/1013