Eaton Electrical Disconnect Switches - Manual (Page 28)

For more information visit us at: www.eatonelectrical.ca
27
December 2004
Fuse Clips for Variable or Flange Mount Operating Mechanisms
Table 27. C351 — Fuse Clip Selection — 3 Poles
ᕃ Fuse clip “R” rejection members for use with Class R fuses are supplied loose in the Fuse Clip Kits.
Note: Kits do not include fuses.
Starter
Size Motor
Voltage Maximum
Horsepower
(3-Phase) Fuse Clip
Rating Fuse Clip Kit for Field Installation with
Non-fusible Starter
Dual Element
Fuses Amperes Volts Catalogue Number Catalogue Number Catalogue Number Catalogue Number
For Non-rejection
Type Fuses For use w/ “R”
Rejection Type Fuses For Form I
Type “J” Fuses For Form II
Type “C” Fuses
0 200/230
460/575 3
5 30
30 250
600 C351KC21
C351KD22-61 C351KC21R
C351KD22-61R –
C351KD71 –
C351KD81
1 200/230
460/575 7-1/2
10
30
30 250
600 C351KC21
C351KD22-61 C351KC21R
C351KD22-61R –
C351KD71 –
C351KD81
2 200
230
460/575 10
15
25 60
60
60 250
250
600 C351KD22-61
C351KD22-61
C351KD62 C351KD22-61R
C351KD22-61R
C351KD62R –
–
C351KD72 –
–
C351KD82
3 200
230
460/575 25
30
50 100
100
100 250
250
600 C351KE23-63 ᕃ
C351KE23-63 ᕃ
C351KE23-63 ᕃ
C351KE23-63 ᕃ
C351KE23-63 ᕃ
C351KE23-63 ᕃ
–
–
C351KE73 –
–
C351KE83
4 200
230
460/575 40
50
100
200
200
200 250
250
600 C351KF24-64 ᕃ
C351KF24-64 ᕃ
C351KF24-64 ᕃ
C351KF24-64 ᕃ
C351KF24-64 ᕃ
C351KF24-64 ᕃ
–
–
C351KF74 –
–
C351KF84
5 200
230
460/575 75
100
200
400
400
400 250
250
600 Not Available
in Kit Form Not Available
in Kit Form Not Available
in Kit Form Not Available
in Kit Form
C351 Fuse Clip Kit
Table 28. Type C361 NEMA 12
Safety Door Hardware
ᕃ The 1/4-inch x 1/2-inch standard mill
rectangular locking bar is not supplied
with these kits.
ᕄ Third roller latch for use with 4 or 6-inch
handle when 3 point latching is required.
Handle Length
(Inches) Catalogue
Number
ᕃ
4
6 C361KJ4
C361KJ6
Roller Latch ᕄ C361KR
NEMA 12 Safety Door Hardware
Product Selection
Type C361 NEMA 12
Safety Door Hardware
Type C361 Door Hardware Kits are
designed to function with all C361 and
C371 disconnect switches and circuit
breaker operating mechanisms.
These kits are designed for use with
small enclosures up to 40 inches
(1016 mm), intermediate 40 – 60 inches
(1016 – 1524 mm) or larger floor cases
over 60 inches (1524 mm) to provide
enclosure sealing and protection
against unauthorized entry. These
kits can be used on enclosure flanges
with material thickness ranging from
16 gauge through 3/16 inches with
flanges on the right side only. Door
hardware kits are to be installed in a
commercially available enclosure.
Consult the enclosure manufacturer
application data for proper kit selection.
Operating Mechanisms with Disconnect Switches
Accessories