Hitachi 308640 - Manual (Page 27)

308640 27
Accessories
Use Only Genuine Graco Parts and Accessories
Grounding Clamp and Wire 222011
12 ga, 25 ft (7.6 m) wire
High Pressure Ball Valves, Viton r Seals
5000 psi (35 MPa, 350 bar) Maximum Working Pressure
Can be used as fluid drain valve.
210657 1/2 npt(m)
210658 3/8 npt(m)
210659 3/8 x 1/4 npt(m)
In-line Fluid Filter 210500
5000 psi (35 MPa, 350 bar) Maximum Working Pressure
100 mesh. Fits onto the gun’s fluid connector. 1/4–18
npsm. Includes the parts shown below.
168517
Filter
164075
210501
205264
Ruby-ball Needle Assembly 236678
Use to decrease wear with acid catalyzed finishes. For
use in place of the standard fluid needle, part no.
238754, item 10
1 on page 19. Use with diffuser-seat
238427 only.
Plastic Needle Kit 240679
4000 psi (28 MPa, 280 bar) Maximum Working Pressure
Includes: Plastic Ball Tipped Needle Assembly 240678,
diffuser-seat, and gasket.
For use with acid catalyzed finishes and for light
viscosity fluids. Use with diffuser-seat 224855 only. Not
recommended for use with AA RAC tips.
Bleed-type Master Air Valve
300 psi (2.1 MPa, 21 bar) Maximum Working Pressure
Relieves air trapped in the air line between the pump
air inlet and this valve when closed.
107141 3/4 npt(m x f) inlet & outlet
107142 1/2 npt(m x f) inlet & outlet
Air Line Quick-disconnect 113367
Consists of:
113410 Coupling, female, quick-disconnect
113368 Coupling, male, quick-disconnect
Brush 101892
For cleaning the gun.
Fluid Swivel Connector 189018
5800 psi (40 MPa, 400 bar) Maximum Working Pressure
To ease movement of the gun and fluid hose. 1/4–18
npsm
Air Whip Hoses
100 psi (0.7 MPa, 7 bar) Maximum Working Pressure
To ease movement of the gun and hose. 1/4–18 npsm,
polyurethane with SST braid.
238759 3 ft. (0.92 m) hose
236873 6 ft. (1.83 m) hose
Air Cap Verification Kit 239897
For air cap 239898 only, to determine air pressure
behind the air cap. Do not use for actual spraying. To
be compliant, atomizing air pressure must not exceed
10 psi (70 kPa, 0.7 bar).
Conversion Kits
Kits to convert from a gun with standard spray tip, tip
guard, and air cap to a gun with the AA RAC assem-
bly. See parts list and drawing below for parts included
with kit.
240462 Use with gun part no. 238402 and 238852
to convert to gun part no. 238851.
240463 Use with gun part no. 238883 to convert to
gun part no. 239001.
Ref.
No.
Part No. Description Qty.
1 238701 AA RAC AIR CAP ASSEMBLY 1
2 192096 RAC HOUSING 1
3 242XXX TIP CYLINDER; tip of choice
Includes item 3a
1
3a 193000 S FLUID SEAT 1
4 239172 DIFFUSER-SEAT; Included with Kit
240462 only
1
239173 DIFFUSER-SEAT, hi-flow; Included
with Kit 240463 only
1
5 187521 GASKET, fluid; acetal homopolymer
(black)
1
1
3a
4
5
06765B
2
3