Pre-assembly, Assembly step 1, Assembly step 2 – Horizon Fitness PREMIER T1201 User Manual

Page 5

Advertising
background image



INTR

ODUC

TION

IMPOR

TANT

PRE
CA

UTIONS

BEF
ORE

YOU
BE

GIN

TREADMILL

OPER

ATION

LIMITED

W

ARR
ANTY

TR

OUBLE

SHOO

TING

&

MAINTENANCE

CONDITIONING

GUIDELINE

S

AS

SEMBL

Y

BEF

ORE

YOU

BE

GIN

AS

SEMBL

Y



INTR

ODUC

TION

IMPOR

TANT

PRE

CA

UTIONS

TREADMILL OPER

ATION

CONDITIONING GUIDELINE

S

TR

OUBLE

SHOO

TING

&

MAINTENANCE

LIMITED

W

ARR

ANTY

BOLT (A)
20 mm
Qty: 6

FLAT WASHER (B)
8 mm
Qty: 4

SPRING WASHER (C)
8 mm
Qty: 6

ARC WASHER (D)
8 mm
Qty: 2

Open HARDWARE BAG 1.

Slide LEFT CONSOLE MAST into MAIN
FRAME BRACKET
.

Insert 2 BOLTS (A), 2 SPRING WASHERS
(C)
and 2 FLAT WASHERS (B) from the
bottom outside of the mast to secure
the CONSOLE MAST to the MAIN
FRAME BRACKET
.

Insert 2 BOLTS (A), 2 SPRING WASHERS
(C)
and 2 FLAT WASHERS (B) from the
bottom inside of the mast to secure the
CONSOLE MAST to the MAIN FRAME
BRACKET
.

Insert 2 BOLTS (A), 2 SPRING WASHERS
(C)
and 2 ARC WASHERS (D) from
the front of the mast to secure the
CONSOLE MAST to the MAIN FRAME
BRACKET
.

A

B

C

D

E

Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt
to lift the treadmill at this time. Remove plastic wrap from console masts.

*NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded
in before completely tightening any ONE bolt. A light application of grease may aid in the installation of
hardware. Any grease, such as lithium bike grease is recommended.

PRE-ASSEMBLY

MAIN FRAME BRACKET

LEFT CONSOLE MAST

BOLTS (A)

FLAT WASHERS (B)

ARC WASHERS (D)

SPRING WASHERS (C)

SPRING WASHERS (C)

BOLTS (A)

FLAT WASHERS (B)

SPRING WASHERS (C)

BOLTS (A)

ASSEMBLY STEP 1

HARDWARE BAG 1 CONTENTS:

ASSEMBLY STEP 2

RIGHT CONSOLE MAST

LEAD WIRE

CONSOLE CABLE

MAIN FRAME BRACKET

RIGHT CONSOLE MAST

BOLTS (A)

FLAT WASHERS (B)

ARC WASHERS (D)

SPRING WASHERS (C)

SPRING WASHERS (C)

BOLTS (A)

FLAT WASHERS (B)

SPRING WASHERS (C)

BOLTS (A)

CONSOLE CABLE

BOLT (A)
20 mm
Qty: 6

FLAT WASHER (B)
8 mm
Qty: 4

SPRING WASHER (C)
8 mm
Qty: 6

ARC WASHER (D)
8 mm
Qty: 2

HARDWARE BAG 2 CONTENTS:

Pull LEAD WIRE through RIGHT
CONSOLE MAST
.

After pulling the lead wire through
the mast, the top of the console cable
should be located at the top of the
mast. Detach and discard lead wire.

Open HARDWARE BAG 2.

Slide RIGHT CONSOLE MAST into MAIN
FRAME BRACKET
.

NOTE: Do not pinch CONSOLE CABLE
when placing the mast onto the main
frame.

Insert 2 BOLTS (A), 2 SPRING
WASHERS (C)
and 2 FLAT WASHERS
(B)
from the bottom outside of the
mast to secure the CONSOLE MAST to
the MAIN FRAME BRACKET.

Insert 2 BOLTS (A), 2 SPRING
WASHERS (C)
and 2 FLAT WASHERS
(B)
from the bottom inside of the mast
to secure the CONSOLE MAST to the
MAIN FRAME BRACKET.

Insert 2 BOLTS (A), 2 SPRING
WASHERS (C)
and 2 ARC WASHERS (D)
from the front of the mast to secure
the CONSOLE MAST to the MAIN
FRAME BRACKET
.

A

B

C

D

E

F

NOTE: Do not completely tighten
any screws or bolts until step 6 is
complete!

NOTE: Do not completely tighten
any screws or bolts until step 6 is
complete!

T1201_Rev.1.7.indd 8-9

7/31/08 4:52:34 PM

Advertising