Horizon Fitness ROJO T5 - Manual (Page 3)

BOLT (A)
20 mm
Qty: 6
FLAT WASHER (B)
8 mm
Qty: 4
SPRING WASHER (C)
8 mm
Qty: 6
ARC WASHER (D)
8 mm
Qty: 2
Open HARDWARE BAG 1. A
B
C
D
E
PRE-ASSEMBLY
MAIN FRAME BRACKET
LEFT CONSOLE MAST
BOLTS (A)
FLAT WASHERS (B)
ARC WASHERS (D)
SPRING WASHERS (C)
SPRING WASHERS (C)
BOLTS (A)
FLAT WASHERS (B)
SPRING WASHERS (C)
BOLTS (A)
ASSEMBLY STEP 1
HARDWARE BAG 1 CONTENTS:
ASSEMBLY STEP 2
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
MAIN FRAME BRACKET
RIGHT CONSOLE MAST
BOLTS (A)
FLAT WASHERS (B)
ARC WASHERS (D)
SPRING WASHERS (C)
SPRING WASHERS (C)
BOLTS (A)
FLAT WASHERS (B)
SPRING WASHERS (C)
BOLTS (A)
CONSOLE CABLE
BOLT (A)
20 mm
Qty: 6
FLAT WASHER (B)
8 mm
Qty: 4
SPRING WASHER (C)
8 mm
Qty: 6
ARC WASHER (D)
8 mm
Qty: 2
HARDWARE BAG 2 CONTENTS:
A
B
C
D
E
F
Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at
this time. Remove plastic wrap from console masts.
*NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely
tightening any ONE bolt. A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike
grease is recommended.
NOTE: Do not completely tighten any
screws or bolts until step 6 is complete!
Slide LEFT CONSOLE MAST into MAIN FRAME
BRACKET.
Insert 2 B OLTS (A), 2 SPRING WASHERS (C)
and 2 FLAT WASHERS (B) from the bottom outside
of the mast to secure the CONSOLEMAST to the
MAINFRAMEBRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C) and
2 FLAT WASHERS (B) from the bottom inside of
the mast to secure the CONSOLEMAST to the
MAINFRAMEBRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C) and2
ARCWASHERS (D) from the front of the mast to
secure the CONSOLEMAST to the MAINFRAME-
BRACKET.
Pull LEAD WIRE through RIGHT CONSOLE
MAST.
After pulling the lead wire through the mast, the
top of the console cable should be located at the
top of the mast. Detach and discard lead wire.
Open HARDWARE BAG 2.
Slide RIGHT CONSOLE MAST into MAIN
FRAME BRACKET.
NOTE: Do not pinch CONSOLE CABLE when
placing the mast onto the main frame.
NOTE: Do not completely tighten any
screws or bolts until step 6 is complete!
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 FLAT WASHERS (B) from the bottom
outside of the mast to secure the CONSOLE
MAST to the MAIN FRAME BRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 FLAT WASHERS (B) from the bottom
inside of the mast to secure the CONSOLE
MAST to the MAIN FRAME BRACKET.
Insert 2 BOLTS (A), 2 SPRING WASHERS (C)
and 2 ARC WASHERS (D) from the front of
the mast to secure the CONSOLE MAST to
the MAIN FRAMEBRACKET.
3 4
2/15/09 10:20 AM