Horizon Fitness E901 - Manual (Page 5)

Be
FO
re
YOU
Be
GiN

iNT
rODUC
TiON
im
PO
rT
ANT
Pre
CA
UT
iONS
AS
Sem
BL
Y
Be
FO
re
YOU
Be
GiN
eLL
iP
TiC
AL
OP
er
AT
iON
Limi
Te
D
W
Arr
ANTY
Tr
OUBL
eSHOO
TiNG
&
m
AiNT
eNANC
e
COND
iT
iON
iNG
GU
iD
eL
iN
eS
Be
FO
re
YOU
Be
Gi
N
AS
Sem
BL
Y
9
iNT
rODUC
Ti
ON
im
PO
rT
ANT
Pre
CA
UT
iONS
eLL
iP
Ti
CAL
OP
er
AT
iON
COND
iT
iON
iNG
GU
iD
eL
iN
eS
Tr
OUBL
eSHOO
Ti
NG
&
m
Ai
NT
eNANC
e
Limi
Te
D
W
Arr
ANTY
ASSEMBLY STeP 2
BOLTS (B)
SPRING WASHERS (C)
FLAT WASHERS (D)
CONSOLE MAST BOOT
CONSOLE CABLE MAIN FRAME
BOLTS (B) ARC WASHERS (E)
CONSOLE MAST
BOLT (B)
20 mm
Qty: 6
SPRING WASHER (C)
15 mm
Qty: 6
FLAT WASHER (D)
20 mm
Qty: 4
ARC
WASHER (E)
17 mm
Qty: 2
angle view
WATER
BOTTLE
HOLDER
CONSOLE
MAST
PRE-ATTACHED
SCREW
Open HArDWAre BAG FOr STeP 2.
Slide CONSOLe mAST BOOT onto the bottom of the CONSOLe mAST above bolt holes as shown above.
Carefully pull the CONSOLe CABLe through the CONSOLe mAST using the twist tie located inside the
CONSOLe mAST.
Attach the CONSOLe mAST to the mAiN FrAme using 2 BOLTS (B), 2 SPriNG WASHerS (C) and 2
FLAT WASHerS (D) in each side and 2 BOLTS (B), 2 SPriNG WASHerS (C) and 2 ArC WASHerS (e) in
the front of the CONSOLe mAST. Slide CONSOLe mAST BOOT down to cover mAiN FrAme.
DO NOT PiNCH WireS!
Attach the WATer BOTTLe HOLDer to the mast using 2 Pre-ATTACHeD SCreWS.
A
B
C
D
e
HArDWAre BAG FOr STeP 2 CONTeNTS :
ASSEMBLY STeP 
NOTe: There is NO hardware bag for this step. All hardware is pre-installed.
Attach the PeDAL Arm COVer to the riGHT PeDAL Arm using Pre-ATTACHeD SCreW.
Attach the rOLLer WHeeL COVer to the riGHT PeDAL Arm using Pre-ATTACHeD SCreW.
Repeat on the other side.
A
B
C
PRE-ATTACHED SCREW
PEDAL ARM
PEDAL ARM COVER
PRE-ATTACHED SCREW
ROLLER WHEEL COVER
E901_Rev.1.7.indd 8-9 9/10/08 11:06:50 AM