Hitachi LE40H405 - Manual (Page 13)

ENGLISH
Starting setup
will assist you to specify the Air/Cable setting and program
your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made.
1
To turn on the TV, touch POWER (POWER indicator on the
front of the unit changes blue. It may take approx. 10 seconds
for a picture to appear on screen.). The Setup Wizard function
begins.
2
Press ▲ or ▼ to select “Source”, then press  or  to select
“Cable” or “Air”.
3
Press ▲ or ▼ to select “Scan”, then press  or SELECT.
4
•
NOTE
•
TV operation
1
To turn on the TV, press POWER.
(POWER indicator on the front of the unit changes blue.
It may take approx. 10 seconds for a picture to appear on
screen.)
2
Adjust the volume level by pressing VOL or . The
volume level will be indicated on the screen by volume bars.
As the volume level increases, so do the number of bars.
If the volume decreases, the number of volume bars also
decreases.
3
Set the Source option to the appropriate position.
4
Press the Direct Channel Selection (0-9, –) buttons to
select the channel.
(If you press only the channel number, channel selection will
be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to select channel
2, press 2, then press SELECT .
10-99: Press the 2 digits in order. Example, to select
channel 12, press 1, 2, then press SELECT.
100-135: Press the 3 digits in order. Example, to select
channel 120, press 1, 2, 0, then press SELECT.
TO SELECT DIGITAL CHANNELS
– button followed by
the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1, then press
SELECT.
• If a channel is selected with only audio content, “Audio
only” will be displayed on the screen.
• If a channel is selected with a weak digital signal, “Weak
Signal or No Audio and Video.” will be displayed on the
screen.
• The same program may be available on either an analog
channel or a digital channel. You may choose to watch
either format.
• If a channel is selected to which you have not subscribed,
“Scrambled ” will be displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air Cable
VHF
2-13
VHF
2-13
UHF
14-69
NOTES
• If a channel with no broadcast is selected, the sound will
automatically be muted.
• It may take a few seconds for a digital channel picture to
appear on screen after being selected.
To select the video input source
To view a signal from another device connected to your LCD TV,
such as a VCR player, press INPUT, then press ▲ or ▼, then
press SELECT.You can select TV, Video, Component, HDMI or
RGB depending on which input jacks you used to connect your
devices.
CH /
Press and release CH / . The channel automatically stops at
the next channel set into memory.
For proper operation, before selecting channels, they should be
set into the memory. Refer to the Channels Menu on page 14.
Input
TV
AV
Component
RGB
HDMI 1
HDMI 2
Tuner
Please select your tuner mode:
Cable
Setup Wizard
Move SEL Select Return
SEL Select
Air
MENU Return Move
If you press EXIT in the process of “Setup Wizard”, the Setup
Wizard stops and changes to the normal screen. When you
make a menu selection, your changes occur immediately. You
do not have to press EXIT to see your changes.
Depending on the reception condition, it may take up to 25
minutes or more to complete memorizing digital cable
channels. Please allow the process to complete without
interruption.
“Setup Wizard” will begin. After the Setup Wizard is
completed, the TV channel appears on the screen.
CATV
Digital Terrestrial Broadcast(8VSB):2-69
Digital cable(64/256 QAM):1-135
1-125