Document Outline

• Telephone Support.pdf
  • Telephone Support
  • Direct to Aerco technical support
• Section 2.pdf
  • Boiler Clearances
  • Lifting Lug Location
  • Supply and Return Location
  • Relief and Drain Valve Location
  • Pressure /Temperature Gauge Installation
  • Pressure/Temperature Gauge Installation
  • Condensate Drain System Location
  • Gas Supply Regulator and Manual Shut -Off Valve Location
  • AC Wiring Box Location
  • Electrical Wiring Diagram
  • Field Control Wiring Box Location
  • Field Control Box Wiring
• Section 3.pdf
  • Figure 3.1
    • Front Panel Controls Location
  • Figure 3.2
    • Temperature Controller Operating Status Lights
  • Figure 3.3
    • Outlet Temperature Display
  • Figure 3.4
    • Percent of Firing Rate Display
  • Figure 3.5
    • Setpoint Display
  • Figure 3.6
    • Auto/ Manual Display with Auto On
  • Figure 3.7
    • Auto/Manual Display with Manual On
  • Figure 3.8
    • Annunciator Function Switches and LCD Display
  • Figure 3.9
    • Combustion Safeguard Status Indicator LED Location
  • Figure 3.10
    • Water Level Test and Reset Switch Locations
  • Figure 3.11
    • Proof of Closure Switch Location
  • Figure 3.12
    • Air/Fuel Valve Open and Engaging the Air/Fuel Valve Open Microswitch
  • Figure 3.13
    • Blower Proof Switch Location
  • Figure 3.14
    • Air/Fuel Valve in Ignition Position, Engaging the Ignition Microswitch
  • Figure 3.15
    • Flame Test Jack Location
• Section 4.pdf
  • 1/8” Gas Plug Location
  • Analyzer Probe Hole Location
  • Differential Regulator Adjustment Tool Installation
  • Air Shutter Locking Nut Location
  • Propane Air Differential Pressure Taps
  • Over Temperature Limit Switch Location
• Section 5.pdf
  • SECTION 5- MODE OF OPERATION
    • 5.1 INDOOR/OUTDOOR RESET MODE
      • 5.1.1 RESET RATIO
      • 5.1.2. BUILDING REFERENCE TEMPERATURE
      • 5.1.3 OUTDOOR AIR SENSOR INSTALLATION
      • 5.1.4 INDOOR / OUTDOOR STARTUP
    • 5
    • 5.2 CONSTANT SETPOINT MODE
    • 5.2.1 SETTING THE SETPOINT
    • 5.3 4 to 20 MILLIAMP REMOTE SETPOINT MODE
      • 5.3.1 4 to 20 MA REMOTE SETPOINT FIELD WIRING
      • 5.3.2 4 to 20 MA REMOTE SETPOINT STARTUP
    • 5.4 4 to 20MA DIRECT DRIVE MODE
      • 5.4.1 4 to 20MA DIRECT DRIVE FIELD WIRING
      • 5.4.2 4 to 20 MA DIRECT DRIVE STARTUP
    • 5.5 BOILER MANAGEMENT SYSTEM (BMS)
      • 5.5.1 BOILER MANAGEMENT SYSTEM EXTERNAL FIELD WIRING
      • 5.5.2 BOILER MANAGEMENT SYSTEM SETUP AND STARTUP
    • 5.6 COMBINATION CONTROL SYSTEM (CCP)
      • 5.6.1 COMBINATION CONTROL SYSTEM FIELD WIRING
      • 5.6.2 COMBINATION CONTROL SYSTEM SETUP AND STARTUP
    • 5.7. USING THE OUTSIDE AIR SENSOR FEATURE
• Section 6.pdf
  • SECTION 6-SAFETY DEVICE TESTING PROCEDURES
    • • • Figure 6.1
          • 1/8” Pipe Plug Position for Manometer installation
        • Figure 6.2
          • Temperature Limit Switch Setting
        • Figure 6.3
          • Manual Leak Detection Valve
        • Figure 6.4
          • Blower Proof Switch Location and Wiring
        • Figure 6.5
          • SSOV Actuator Set Screw Location
        • Figure 6.6
          • Air/Fuel Valve Cover Screw Locations
        • Figure 6.7
          • Air/Fuel Valve Open Position Switch Location
• Section 7.pdf
  • Figure 7.1
    • Spark Ignitor and Flame Detector Location
  • Figure 7.2
    • Grounding Terminal Location
  • Figure 7.3
    • Burner Disassembly Diagram
  • Figure 7.4
    • Exhaust Sensor Connector Location
  • Figure 7.5
    • Blower Proof Switch Wire Locations
  • Figure 7.6
    • Air/Fuel Valve Inlet Hose Clamp
  • Figure 7.7
    • Feedback Tube and Air/Fuel Valve to Differential Regulator Bolts
  • Figure 7.8
    • Manifold Nut and Bolt Locations
  • Figure 7.9
    • Propane Unit Component Location
• Section 8.pdf
  • 8.1 LOW GAS PRESSURE
    • 8.1.1 Low Supply Gas Pressure
    • 8.1.2 Gas Pressure Switches
    • 8.1.1 LOW SUPPLY GAS PRESSURE
    • 8.1.2 LOW GAS PRESSURE SWITCH
  • 8.2 HIGH GAS PRESSURE
    • 8.2.3 HIGH GAS PRESSURE SWITCH