Document Outline

• 1. Introduction
• 2. The J-Series line array
  • 2.1 Number of cabinets required
  • 2.2 J-SUB subwoofer setup
    • 2.2.1 J-SUB ground stacks
    • 2.2.2 J-SUBs flown on top of a J8/J12 array
    • 2.2.3 Flown J-SUB columns
    • 2.2.4 J-SUB horizontal SUB array
  • 2.3 J-SUB/J-INFRA subwoofer setup
    • 2.3.1 Combined J-INFRA/J-SUB ground stacks
    • 2.3.2 Flown J-SUBs, J-INFRA ground stacks
    • 2.3.3 Flown J-SUBs, J-INFRA SUB array
• 3. The V-Series line array
  • 3.1 Number of cabinets required
  • 3.2 V-SUB subwoofer setup
    • 3.2.1 V-SUB ground stacks
    • 3.2.2 V-SUBs flown on top of a V8/V12 array
    • 3.2.3 Flown V-SUB columns
    • 3.2.4 V-SUB horizontal SUB array
  • 3.3 V-, J-SUB/J-INFRA subwoofer setup
    • 3.3.1 Combined J-, V-SUB ground stacks
    • 3.3.2 Flown V-, J-SUBs or J-INFRA ground stacks
    • 3.3.3 Flown V-SUBs, J-INFRA SUB array
• 4. The Y-Series line array
  • 4.1 Number of cabinets required
  • 4.2 Y-SUB subwoofer setup
    • 4.2.1 Y-SUB ground stacks
    • 4.2.2 Y-SUBs flown on top of a Y8/Y12 array
    • 4.2.3 Flown Y-SUB columns
    • 4.2.4 Y-SUB horizontal SUB array
  • 4.3 V-, Y-, J-SUB/J-INFRA subwoofer setup
    • 4.3.1 Combined J-, Y-SUB ground stacks
    • 4.3.2 Flown Y-, J-SUBs or J-INFRA ground stacks
    • 4.3.3 Flown Y-SUBs, J-INFRA SUB array
• 5. The Q-Series line array
  • 5.1 Number of cabinets required
  • 5.2 Subwoofer setup
• 6. The T-Series line array
  • 6.1 Number of cabinets required
  • 6.2 Subwoofer setup
• 7. The xA-Series line array
  • 7.1 Number of cabinets required
  • 7.2 Subwoofer setup
• 8. The d&b point sources
  • 8.1 Number of cabinets required
• 9. Column loudspeakers
• 10. ArrayCalc
  • 10.1 ArrayCalc installation
  • 10.2 Starting ArrayCalc
  • 10.3 ArrayCalc menu options and Toolbar
    • 10.3.1 File menu
    • 10.3.2 View menu
    • 10.3.3 Sources menu
    • 10.3.4 Extras / Options menu
    • 10.3.5 Help menu
  • 10.4 ArrayCalc workspace
  • 10.5 Venue page
    • 10.5.1 General data input
    • 10.5.2 Project settings
    • 10.5.3 Venue editor
  • 10.6 Sources page
    • 10.6.1 Adding and deleting sources
  • 10.7 Line Arrays
    • 10.7.1 Array settings
    • 10.7.2 Auto Splay
    • 10.7.3 Copy, Paste, Paste as new
    • 10.7.4 Mechanical load conditions for arrays
    • 10.7.5 Array view and load distribution
    • 10.7.6 Top view diagram for arrays
    • 10.7.7 Profile at array aiming
    • 10.7.8 SPL plot and signal selection for arrays
    • 10.7.9 Maximum SPL and headroom
    • 10.7.10 Air absorption, HFC circuit
    • 10.7.11 Array EQ / CPL
    • 10.7.12 Level adjustment (Lev/dB)
    • 10.7.13 Horizontal arrays of J8, V8, Y8, Q1 and T10 columns
  • 10.8 Point sources
  • 10.9 Column loudspeakers
    • 10.9.1 Point source SPL mapping
    • 10.9.2 Simulation limits
  • 10.10 SUB arrays
    • 10.10.1 General considerations on stacked subwoofer placement
    • 10.10.2 L/R ground stack
    • 10.10.3 Design criteria
    • 10.10.4 Physical placement of cabinets
    • 10.10.5 Shaping the wavefront using delays
    • 10.10.6 SUB array settings
    • 10.10.7 Mixed arrays of J-, V-SUBs and J-INFRAs
    • 10.10.8 Dispersion displays
  • 10.11 Alignment page
    • 10.11.1 Time alignment of SUB arrays
  • 10.12 3D plot page
  • 10.13 Amplifiers page
    • 10.13.1 Create R1 files
    • 10.13.2 Patches
    • 10.13.3 Patch dialog
    • 10.13.4 Cabinets section
  • 10.14 Snapshot manager
  • 10.15 Rigging plot page
  • 10.16 Parts list page
  • 10.17 Ground stacked setups
  • 10.18 CPL circuit
  • 10.19 Time alignment
    • 10.19.1 Subwoofers
    • 10.19.2 Nearfills
    • 10.19.3 Horizontal array
  • 10.20 Equalization
• 11. ArrayProcessing
  • 11.1 Motivation and benefits
  • 11.2 How does it work?
  • 11.3 ArrayProcessing workflow
  • 11.4 ArrayProcessing dialog