Document Outline

• Front Cover
• FOR SAFE OPERATION
• Revision History
• Preface
• Contents
  • Illustrations
    • Figures
    • Tables
• CHAPTER 1 Command Processing
  • 1.1 Command Format
  • 1.2 Status Byte
  • 1.3 Outline of Command Processing
    • 1.3.1 Single commands
    • 1.3.2 Command link
    • 1.3.3 Disconnect/reconnect processing
    • 1.3.4 Synchronous mode data transfer/wide mode data transfer
  • 1.4 Command Queuing Function
    • 1.4.1 Untagged queuing
    • 1.4.2 Tagged queuing
  • 1.5 UNIT ATTENTION Condition
    • 1.5.1 Generation of the UNIT ATTENTION condition
    • 1.5.2 Response and release condition at UNIT ATTENTION condition hold state
    • 1.5.3 UNIT ATTENTION condition multiple hold
  • 1.6 Sense Data Hold State
    • 1.6.1 Sense data hold condition
    • 1.6.2 Response and release conditions at sense data hold state
  • 1.7 Command Processing Exceptions
    • 1.7.1 Overlapping commands
    • 1.7.2 Illegal LUN specification
    • 1.7.3 Reserved operation code
    • 1.7.4 Command processing in the not ready state
    • 1.7.5 Error recovery processing
    • 1.7.6 Reset processing
    • 1.7.7 Fatal hardware errors
  • 1.8 Data Block Addressing
    • 1.8.1 Definition of data space
    • 1.8.2 Logical block addressing
• CHAPTER 2 Data Buffer Management
  • 2.1 Data Buffer
    • 2.1.1 Data buffer configuration and basic operation
    • 2.1.2 Operation mode setting
  • 2.2 Look-Ahead Cache Feature
    • 2.2.1 Caching operation
    • 2.2.2 Caching parameters
    • 2.2.3 Look-Ahead operation, Look-Ahead volume
  • 2.3 Write Cache
• CHAPTER 3 Command Specifications
  • 3.1 Control/Sense Commands
    • 3.1.1 TEST UNIT READY (00)
    • 3.1.2 INQUIRY (12)
    • 3.1.3 READ CAPACITY (25)
    • 3.1.4 CHANGE DEFINITION (40)
    • 3.1.5 MODE SELECT (15)
    • 3.1.6 MODE SELECT EXTENDED (55)
    • 3.1.7 MODE SENSE (1A)
    • 3.1.8 MODE SENSE EXTENDED (5A)
    • 3.1.9 REZERO UNIT (01)
    • 3.1.10 START/STOP UNIT (1B)
    • 3.1.11 RESERVE (16)
    • 3.1.12 RESERVE EXTENDED (56)
    • 3.1.13 RELEASE (17)
    • 3.1.14 RELEASE EXTENDED (57)
    • 3.1.15 REQUEST SENSE (03)
    • 3.1.16 LOG SELECT (4C)
    • 3.1.17 LOG SENSE (4D)
    • 3.1.18 PERSISTENT RESERVE IN (5E)
    • 3.1.19 PERSISTENT RESERVE OUT (5E)
    • 3.1.20 REPORT LUNS (A0)
    • 3.1.21 REPORT DEVICE IDENTIFIER (A3)
    • 3.1.22 SET DEVICE IDENTIFIER (A4)
  • 3.2 Data Access Commands
    • 3.2.1 READ (08)
    • 3.2.2 READ EXTENDED (28)
    • 3.2.3 WRITE (0A)
    • 3.2.4 WRITE EXTENDED (2A)
    • 3.2.5 WRITE AND VERIFY (2E)
    • 3.2.6 VERIFY (2F)
    • 3.2.7 SEEK (0B)
    • 3.2.8 SEEK EXTENDED (2B)
    • 3.2.9 SET LIMITS (33) (Not Supported)
    • 3.2.10 SYNCHRONIZE CACHE (35)
  • 3.3 Format Commands
    • 3.3.1 FORMAT UNIT (04)
    • 3.3.2 REASSIGN BLOCKS (07)
    • 3.3.3 READ DEFECT DATA (37)
  • 3.4 Maintenance, Diagnostic Commands
    • 3.4.1 SEND DIAGNOSTIC (1D)
    • 3.4.2 RECEIVE DIAGNOSTIC RESULTS (1C)
    • 3.4.3 WRITE BUFFER (3B)
    • 3.4.4 READ BUFFER (3C)
    • 3.4.5 READ LONG (3E)
    • 3.4.6 WRITE LONG (3F)
    • 3.4.7 WRITE SAME (41)
• CHAPTER 4 Parameter Data Formats
  • 4.1 Mode Parameters
    • 4.1.1 Read/Write error recovery parameters (page code = 1)
    • 4.1.2 Disconnect/reconnect parameters (page code = 2)
    • 4.1.3 Format parameter (page code = 3)
    • 4.1.4 Drive parameter (page code = 4)
    • 4.1.5 Verify error recovery parameters (page code = 7)
    • 4.1.6 Caching parameters (page code = 8)
    • 4.1.7 Control mode parameters (page code = 0A)
    • 4.1.8 Notch parameter (page code = 0C)
    • 4.1.9 Informational exceptions control page (page code = 1C)
    • 4.1.10 Additional error recovery parameters (page code = 21)
  • 4.2 Log Parameters
    • 4.2.1 Supprot log page (X'00')
    • 4.2.2 Buffer overrun / underrun page (X'01')
    • 4.2.3 Write error count page (X'02')
    • 4.2.4 Read error count page (X'03')
    • 4.2.5 Verify error count page (X'05')
    • 4.2.6 Non-medium error count page (X'06')
    • 4.2.7 Temperature page (X'0D')
    • 4.2.8 Start-stop cycle counter page (X'0E')
    • 4.2.9 Application client page (X'0F')
    • 4.2.10 Self-test result page (X'10')
    • 4.2.11 SMART status page (X'2F')
    • 4.2.12 SMART data page (X'38')
• CHAPTER 5 Sense Data Error Recovery Methods
  • 5.1 Sense Data
    • 5.1.1 Sense data format
    • 5.1.2 Sense data basic information
  • 5.2 INIT Error Recovery Methods (Recommended)
    • 5.2.1 Termination status analysis and error recovery methods
    • 5.2.2 Sense data analysis and error recovery methods
    • 5.2.3 Error logging
  • 5.3 Disk Drive Error Recovery Processing
    • 5.3.1 Error states and retry processing procedures
    • 5.3.2 Auto alternate block allocation processing
    • 5.3.3 Error recovery processing control
• CHAPTER 6 Disk Media Management
  • 6.1 Defect Management
  • 6.2 Disk Media Initialization
    • 6.2.1 Initialization during installation
    • 6.2.2 Re-initialization
  • 6.3 Data Block Verification Methods (Recommended)
  • 6.4 Alternate Block Allocation Processing
• Glossary
• Acronyms and Abbreviations
• Index
• READER’S COMMENT FORM
• Back Cover