Document Outline

• Introduction and Safety
  • Introduction
  • Safety
    • Safety terminology and symbols
    • Environmental safety
    • User safety
    • Safety regulations for Ex-approved products in potentially explosive atmospheres
  • Product warranty
• Transportation and Storage
  • Inspect the delivery
    • Inspect the package
    • Inspect the unit
  • Transportation guidelines
    • Pump handling
    • Lifting methods
  • Storage guidelines
    • Pump storage requirements
• Product Description
  • General description
  • Nameplate information
• Installation
  • Preinstallation
    • Pump location guidelines
    • Foundation requirements
  • Baseplate-mounting procedures
    • Prepare the baseplate for mounting
    • Install the baseplate using shims or wedges
    • Install the baseplate using jackscrews
    • Baseplate-leveling worksheet
  • Pump-to-driver alignment
    • Alignment checks
    • Permitted indicator values for alignment checks
      • Cold settings for parallel vertical alignment
    • Alignment measurement guidelines
    • Attach the dial indicators for alignment
    • Pump-to-driver alignment instructions
      • Perform angular alignment for a vertical correction
      • Perform angular alignment for a horizontal correction
      • Perform parallel alignment for a vertical correction
      • Perform parallel alignment for a horizontal correction
      • Perform complete alignment for a vertical correction
      • Perform complete alignment for a horizontal correction
  • Grout the baseplate
  • Piping checklists
    • General piping checklist
    • Suction-piping checklist
    • Discharge piping checklist
    • Final piping checklist
• Commissioning, Startup, Operation, and Shutdown
  • Preparation for startup
  • Remove the coupling guard
  • Check the rotation - Frame Mounted
  • Check the rotation - Close Coupled
  • Couple the pump and driver
    • Install the coupling guard
  • Bearing lubrication
    • Lubricating-oil requirements
    • Acceptable oil for lubricating bearings
    • Lubricate the bearings with oil
    • Greased-for-life bearing lubrication
  • Pump priming
    • Prime the pump with the suction supply above the pump
    • Prime the pump with the suction supply below the pump
    • Other methods of priming the pump
  • Start the pump
    • Minimum continuous recommended flow
  • Pump operation precautions
  • Shut down the pump
  • Make the final alignment of the pump and driver
• Maintenance
  • Maintenance schedule
  • Bearing maintenance
  • Disassembly
    • Disassembly precautions
    • Required tools
    • Prepare the pump for disassembly
    • Remove the frame assembly and shaft (frame-mounted pump)
    • Remove the frame assembly and shaft (close-coupled pump)
    • Disassemble the liquid end
  • Pre-assembly inspections
    • Replacement guidelines
    • Magnet inspections
    • Bearing-frame inspection
    • Bearings inspection
    • Minimum running clearances
  • Reassembly
    • Reassemble the frame assembly and shaft (frame-mounted pumps)
    • Reassemble the frame assembly and shaft (close-coupled pumps)
    • Reassemble the liquid end
    • Complete the pump reassembly
    • Bolt torque values
• Troubleshooting
  • Operation troubleshooting
  • Alignment troubleshooting
• Parts Listings and Cross-Sectionals
  • Close-coupled S-group (all) and M-group (2 x 3 - 8 only) — stainless steel
  • Close-coupled S-group (all) and M-group (2 x 3 - 8 only) — Hastelloy-C
  • S-group with bearing frame — stainless steel
  • S-group with bearing frame — Hastelloy-C
  • Frame cooling options
  • M-group with bearing frame — stainless steel
  • M-group with bearing frame — Hastelloy-C
  • Spare and repair parts
  • Interchangeability drawings
• Other Relevant Documentation or Manuals
  • Condensed power monitor
• Local ITT Contacts
  • Regional offices