Document Outline

• User manual
• Table of contents
• 1 Introduction
  • 1.1 Safety instructions
  • 1.2 Description
    • 1.2.1 Overview
    • 1.2.2 Display
    • 1.2.3 Keypad
  • 1.3 Putting into operation
    • 1.3.1 Selecting or changing the location
    • 1.3.2 Connecting the power supply
• 2 Operation
  • 2.1 Switching on and off
  • 2.2 Zeroing / Zero point correction
  • 2.3 Simple weighing
  • 2.4 Weighing with tare
    • 2.4.1 Taring
    • 2.4.2 Clearing the tare
    • 2.4.3 Automatic taring
    • 2.4.4 Numerical tare weight entry
    • 2.4.5 Taring by calling up a saved tare value
    • 2.4.6 Chain tare
  • 2.5 Displaying the capacity available
  • 2.6 Dynamic weighing
  • 2.7 Weighing-in to a target weight and checkweighing
    • 2.7.1 Saving target weights
    • 2.7.2 Calling up target weights
    • 2.7.3 Weighing-in
    • 2.7.4 Checkweighing
    • 2.7.5 Clearing the saved target weights
  • 2.8 Working with identifications
    • 2.8.1 Entering identification
    • 2.8.2 Displaying identification
    • 2.8.3 Clearing identifications
  • 2.9 Printing results
  • 2.10 Displaying info
  • 2.11 Switching scales
  • 2.12 Totalising
    • 2.12.1 Totalising items
    • 2.12.2 Subtracting items
    • 2.12.3 Completing totalising
    • 2.12.4 Calling up sum information
  • 2.13 Cleaning
• 3 Counting
  • 3.1 Counting parts into a container
  • 3.2 Counting parts out of a container
  • 3.3 Counting with variable reference quantity
  • 3.4 Counting with minimum accuracy
  • 3.5 Reference optimization
    • 3.5.1 Automatic reference optimization
  • 3.6 Counting with automatic reference determination
  • 3.7 Counting with a known average piece weight
  • 3.8 Counting by calling up a saved average piece weight
    • 3.8.1 Saving average piece weights
    • 3.8.2 Calling up average piece weights
    • 3.8.3 Clearing saved average piece weights
  • 3.9 Counting by calling up a saved target quantity
    • 3.9.1 Saving target quantities
    • 3.9.2 Calling up target quantities
    • 3.9.3 Counting in to target quantities
    • 3.9.4 Clearing saved target quantities
  • 3.10 Counting with two scales
    • 3.10.1 Counting with a reference scale
    • 3.10.2 Counting with a bulk scale
    • 3.10.3 Counting with an auxiliary scale
• 4 Settings in the menu
  • 4.1 Operating the menu
    • 4.1.1 Calling up the menu and entering the password
    • 4.1.2 Selecting and setting parameters
  • 4.2 Overview
  • 4.3 Scale settings (SCALE)
    • 4.3.1 SCALE1/SCALE2 - Selecting scale
    • 4.3.2 CAL - calibration (adjustment)
    • 4.3.3 DISPLAY - weighing unit and display accuracy
    • 4.3.4 TARE - tare function
    • 4.3.5 ZERO - automatic zero update
    • 4.3.6 RESTART - automatic saving of zero point and tare value
    • 4.3.7 FILTER - adaptation to the ambient conditions and the weighing type
    • 4.3.8 FACT - automatic temperature-dependent adjustment
    • 4.3.9 MIN.WEIG - minimum weight
    • 4.3.10 RESET - resetting scale settings to factory settings
  • 4.4 Application settings (APPLICATION)
    • 4.4.1 COUNT - settings for counting
    • 4.4.2 ACCUMULATION - totalising
    • 4.4.3 CHECKWEIGHING
    • 4.4.4 MEMORY - configuring memory
    • 4.4.5 INFO-KEY - assignment of the Info key
    • 4.4.6 AVERAGE - determining the average weight for an unstable load
    • 4.4.7 RESET - resetting application settings to factory settings
  • 4.5 Terminal settings (TERMINAL)
    • 4.5.1 DEVICE - Sleep mode, energy-saving mode and display backlighting
    • 4.5.2 ACCESS - password for Supervisor menu access
    • 4.5.3 RESET - resetting terminal settings to the factory settings
  • 4.6 Configuring interfaces (COMMUNICATION)
    • 4.6.1 COM1/COM2 -> MODE - operating mode of the serial interface
    • 4.6.2 COM1/COM2 -> PRINTER - settings for protocol printout
    • 4.6.3 COM1/COM2 -> PARAMET - communication parameter
    • 4.6.4 COM1/COM2 -> RESET COM1/RESET COM2 - resetting serial interface to factory settings
    • 4.6.5 OPTION - configuring options
    • 4.6.6 DEF.PRN - configuring templates
  • 4.7 Diagnosis and printing out of the menu settings (DIAGNOS)
• 5 Interface description
  • 5.1 SICS interface commands
    • 5.1.1 Available SICS commands
    • 5.1.2 Requirements for communication between scale and PC
    • 5.1.3 Notes on network operation via the optional interface RS422/485
  • 5.2 TOLEDO Continuous mode
    • 5.2.1 TOLEDO Continuous commands
    • 5.2.2 Output format in TOLEDO Continuous mode
• 6 Event and error messages
• 7 Technical data and accessories
  • 7.1 Technical data
    • 7.1.1 Type key
    • 7.1.2 General data
    • 7.1.3 Weighing ranges and readability BBA4..
    • 7.1.4 Weighing ranges and readability BBK4..
    • 7.1.5 Dimensions
    • 7.1.6 Net weights
    • 7.1.7 Interface connections
    • 7.1.8 Assignment of the interface connections
  • 7.2 Accessories
• 8 Appendix
  • 8.1 Information for certified scales in EC countries
  • 8.2 Safety checks
  • 8.3 Table of Geo Values
    • 8.3.1 GEO VALUES 3000e, OIML Class III (European Countries)
    • 8.3.2 GEO VALUES 6000e/7500e OIML Class III
  • 8.4 Sample protocols
• 9 Index