Document Outline

• Operating Manual PNOZ s30
• Preface
• Contents
• 1 Introduction
  • 1.1 Validity of documentation
  • 1.2 Retaining the documentation
  • 1.3 Definition of symbols
• 2 Overview
  • 2.1 Unit structure
    • 2.1.1 Range
    • 2.1.2 Unit features
  • 2.2 Front/side view
• 3 Safety
  • 3.1 Intended use
  • 3.2 Safety regulations
    • 3.2.1 Use of qualified personnel
    • 3.2.2 Warranty and liability
    • 3.2.3 Disposal
    • 3.2.4 For your safety
• 4 Function description
  • 4.1 Introduction
  • 4.2 Block diagram
  • 4.3 Functions
    • 4.3.1 Timing diagram for speed monitoring
  • 4.4 Speed configuration
    • 4.4.1 Select Inputs
    • 4.4.2 Switch functions
    • 4.4.3 Basic configuration
    • 4.4.4 Chip card
  • 4.5 Input device types
    • 4.5.1 Proximity switch
    • 4.5.2 Rotary encoders
      • 4.5.2.1 Output signals
      • 4.5.2.2 Adapter for incremental encoders
• 5 Installation
  • 5.1 General installation guidelines
    • 5.1.1 Dimensions
• 6 Commissioning
  • 6.1 Wiring
    • 6.1.1 General wiring guidelines
    • 6.1.2 Pin assignment of RJ45 socket
    • 6.1.3 Supply voltage
    • 6.1.4 Connection of proximity switches
    • 6.1.5 Connection of a rotary encoder
      • 6.1.5.1 Connect rotary encoder to speed monitor
      • 6.1.5.2 Connect rotary encoder with Z index to speed monitor
      • 6.1.5.3 Connect rotary encoder to the speed monitor via an adapter
    • 6.1.6 Connection of proximity switch and rotary encoder
    • 6.1.7 Reset circuit
    • 6.1.8 Feedback circuit
    • 6.1.9 Select inputs
    • 6.1.10 Semiconductor outputs
    • 6.1.11 EMC-compliant wiring
  • 6.2 Display menu - Configuration
    • 6.2.1 Create configuration overview
    • 6.2.2 Operate rotary knob
    • 6.2.3 Configure Speed Monitor
    • 6.2.4 Password protection
    • 6.2.5 Use chip card
      • 6.2.5.1 Insert chip card
      • 6.2.5.2 Write data to chip card
      • 6.2.5.3 Read data from chip card
      • 6.2.5.4 Transfer device parameters
      • 6.2.5.5 Duplicate chip card
    • 6.2.6 Menu overview
      • 6.2.6.1 Permanent display
      • 6.2.6.2 Basic settings Ini pnp pnp
      • 6.2.6.3 Basic settings for the rotary encoder
      • 6.2.6.4 Settings
      • 6.2.6.5 Advanced settings
      • 6.2.6.6 Information
    • 6.2.7 Example: Configure basic configuration 2
• 7 Operation
  • 7.1 Display elements for device diagnostics
    • 7.1.1 LEDs
    • 7.1.2 Display
      • 7.1.2.1 Error stack entries
      • 7.1.2.2 Current error messages
      • 7.1.2.3 Open circuit message
      • 7.1.2.4 Frequency difference message on proximity switch
• 8 Technical details
  • 8.1 Safety characteristic data
• 9 Supplementary data
  • 9.1 Service life graph of output relays
  • 9.2 Categories
    • 9.2.1 Safety level
    • 9.2.2 Safety functions
    • 9.2.3 Safety-related characteristic data for operation with non-safety-related rotary encoder without additional requirements
      • 9.2.3.1 Permitted encoder types and output signals
      • 9.2.3.2 Safety-related architecture
      • 9.2.3.3 Achievable safety level
    • 9.2.4 Safety-related characteristic data for operation with non-safety-related rotary encoder with mechanical fault exclusion
      • 9.2.4.1 Permitted encoder types and output signals
      • 9.2.4.2 Safety-related architecture
      • 9.2.4.3 Achievable safety level
    • 9.2.5 Safety-related characteristic data for operation with non-safety-related rotary encoder with diagnostics via the drive controller
      • 9.2.5.1 Permitted encoder types and output signals
      • 9.2.5.2 Requirements of the drive controller
      • 9.2.5.3 Safety-related architecture
      • 9.2.5.4 Achievable safety level
    • 9.2.6 Safety-related characteristic data for operation with a safe rotary encoder
      • 9.2.6.1 Permitted encoder types and output signals
      • 9.2.6.2 Safety-related architecture
      • 9.2.6.3 Achievable safety level
    • 9.2.7 Safety-related characteristic data for operation with a safe rotary encoder with Z index
      • 9.2.7.1 Permitted encoder types and output signals
      • 9.2.7.2 Safety-related architecture
      • 9.2.7.3 Achievable safety level
    • 9.2.8 Safety-related characteristic data for operation with non-safety-related rotary encoder and proximity switch
      • 9.2.8.1 Permitted encoder types and output signals
      • 9.2.8.2 Safety-related architecture
      • 9.2.8.3 Achievable safety level
    • 9.2.9 Safety-related characteristic data for operation with 2 proximity switches
      • 9.2.9.1 Permitted encoder types and output signals
      • 9.2.9.2 Safety-related architecture
      • 9.2.9.3 Achievable safety level
  • 9.3 Examples
    • 9.3.1 Connection of proximity switch
      • 9.3.1.1 Features
      • 9.3.1.2 Configuration overview
      • 9.3.1.3 Connection
    • 9.3.2 Incremental encoder connection
      • 9.3.2.1 Features
      • 9.3.2.2 Configuration overview
      • 9.3.2.3 Connection
• 10 Order reference
• Contact address