Document Outline

• FM Steiw/FM-AM Receiver
  • NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM
  • IMPORTANT
  • For the customers in Canada
  • i-CAUTION:
  • Introduction
  • Precautions
    • TV/video programs
    • Tuner
    • DOLBY PRO LOGIC
    • Sound field (combination of digital delayed surround and tone controls)
    • Remote commander
    • On safety
    • On operation
    • On cleaning the cabinet
    • For the customers in the U.S.A.
    • I Chapter 1 Getting Started
  • Unpacking
    • To prevent internal heat buildup in the unit,
    • To avoid damage caused by battery leakage and corrosion
    • Battery life
  • Hooking Up the System
    • For areas with difficult AMI reception
    • Speaker impedance and power capability
    • Note
    • Caution
  • Parts Identification
  • Parts Identification
    • QD Receiver control section
    • d] other equipment control section
    • d SYSTEMnrV mode switch
  • Operating with the Remote Commander
    • List of operative buttons in SYSTEiM mode (When setting the SYSTEiM/TV seiector to SYSTEM
    • Operating the equipment
    • To operate other unit temporariiy without changing the settings of FUNCTiON
    • Note
  • Adjusting Basic Audio Controls
    • IMPORTANT
    • To adjust volume
    • To reduce the sound to a low level temporarily (- 20 dB attenuation)
  • Selecting a Program Source
    • 2 start playback of the selected program.
    • To change the turn-off time
    • To check the remaining time of the sieep timer
  • Selecting a Program Source
    • If you input an already store source under any other index name
    • To switch the display mode between the original function name display and created index name display
    • 1 Select the program source.
    • 2 Press CURSOR MODE to select the INDEX mode.
    • 3 Create an index name.
    • Press TUNER.
    • Select FM or AM.
    • Press DIRECT.
    • 4 Enter the frequency.
    • To correct the entered frequency
    • For entering AM frequencies
    • if you enter a frequency not covered by the tuning interval
    • When the entered frequency does not exist in the receivable frequency range
    • When an FM stereo program is noisy
    • If the automatic scan stops frequently (for FM reception only)
    • To receive all receivable stations again
  • 1
    • Tune in the desired station:
    • Press MEMORY.
    • 4 Whiie MEMORY appears, ^iect the memory page (A,BorC).
    • Replacing a preset station
    • Press TUNER.
    • Select the memory page (A, B, or C).
    • 3 Designate the desired preset station number with the numeric button.
    • IMPORTANT
    • Press TUNER.
    • Tune in the desired station with Preset Tuning.
    • 3 Press CURSOR iNODE to seiect the iNDEX mode.
    • Create an index name.
    • Repeat steps 2 through 4 for aii other stations you want to assign an index name.
    • if you store an aiready categorized station under any other index name
    • To display the frequency and index name of preset stations
  • Receiving Broadcasts
    • Press TUNER.
    • Press FREQ/INDEX to set to the INDEX mode.
    • Select the desired station.
    • Select VIDEO 1, VIDEO 2/LD or VIDEO 3 (STR- D990 only).
    • Turn on the monitor TV.
    • Select the desired program on the TV tuner or the VCR.
    • Select TUNER and tune in the FM simulcast TV program on the receiver.
  • Recording an Audio Source
  • 1
    • Select the desired program source with the function selector. |
    • 2 Set the tape (DAT) deck in the recording mode.
    • 3 Start playback of the selected program source.
    • Note on recording
    • Monitoring the recorded sound
    • 1 Insert the recorded tape into tape deck 1 (or the OAT deck).
    • 2 Insert a blank tape into tape deck 2 and adjust the recording level.
    • 3 Press TAPE 1 or DAT to select the deck for playback.
    • With the STR-D990
    • Select the playback VCR with EDIT VIDEO.
    • Set the playback VCR to the playback mode.
    • 4 Set the VCR 1 to the recording mode.
    • — Video editing —
    • To view the other video source(s) on the monitor TV during dubbing
    • To listen to an audio program during video tape dubbing
    • With the STR-D790
    • Press VIDEO 2/LD.
    • 2 Set VCR 2 to the playback mode.
    • 3 Set the VCR 1 to the recording mode.
    • To listen to an audio program during video tape dubbing
    • To record a TV program
    • With the STR-D990
    • 1 Select the playback VCR with EDIT VIDEO.
    • Set the playback VCR to the playback mode.
    • 3 At the point where audio cjubblng starts, press the pause button on the playback VCR.
    • Press EDIT AUDIO.
    • Select the audio program source with the function selectors.
    • 6 Releasethepausemodeof the playback VCR and set the VCR 1 to the recording mode.
    • 7 Start playback of the selected audio program source.
  • Editing a Video Source
    • Chapter 3 Advanced Operaltiona
  • Getting Ready for Dolby Surround Sound
    • NORMAL mode
    • 3CH. (Channel) LOGIC mode
    • Even for video software which does not carry the
  • Getting Ready for Dolby Surround Sound
    • i POWER-»onI 14 2 6
    • 1 Press SOUND nELOONfOFF to ON.
    • 2 Press DOLBY SUR.
    • Select a program source with the function selector and start playback.
    • 4 Select the Dolby pro logic mode with the DOLBY PRO LOGIC MODE button according to your speaker system.
    • Press T. TONE on the remote commander to set toon.
    • Sequence of the test tone
  • Adjusting the Surround Sound
    • —for Dolby surround mode
    • Press DOLBY SUR.
    • Press CURSOR MODE.
    • 4 Press A or V to select the delay time mode and adjust the delay time with ^ or >.
    • To turn off the surround effect
    • Note
  • Sound Field Settings
  • Sound Field Settings
    • Tune in a station or select the program source to be linked with sound fieid data.
    • Notes
  • Specifications
  • Specifications
    • DirBctly tuning in an FM or AM elation
    • Labeling the preset stations
    • Calling up the SOUND FIEiJ) netting
    • To change the Bettings of FUNCTION