Sony STR-D790 User Manual
Fm steiw/fm-am receiver
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- FM Steiw/FM-AM Receiver
- NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM
- IMPORTANT
- For the customers in Canada
- i-CAUTION:
- Introduction
- Precautions
- Unpacking
- Hooking Up the System
- Parts Identification
- Parts Identification
- Operating with the Remote Commander
- Adjusting Basic Audio Controls
- Selecting a Program Source
- Selecting a Program Source
- If you input an already store source under any other index name
- To switch the display mode between the original function name display and created index name display
- 1 Select the program source.
- 2 Press CURSOR MODE to select the INDEX mode.
- 3 Create an index name.
- Press TUNER.
- Select FM or AM.
- Press DIRECT.
- 4 Enter the frequency.
- To correct the entered frequency
- For entering AM frequencies
- if you enter a frequency not covered by the tuning interval
- When the entered frequency does not exist in the receivable frequency range
- When an FM stereo program is noisy
- If the automatic scan stops frequently (for FM reception only)
- To receive all receivable stations again
- 1
- Tune in the desired station:
- Press MEMORY.
- 4 Whiie MEMORY appears, ^iect the memory page (A,BorC).
- Replacing a preset station
- Press TUNER.
- Select the memory page (A, B, or C).
- 3 Designate the desired preset station number with the numeric button.
- IMPORTANT
- Press TUNER.
- Tune in the desired station with Preset Tuning.
- 3 Press CURSOR iNODE to seiect the iNDEX mode.
- Create an index name.
- Repeat steps 2 through 4 for aii other stations you want to assign an index name.
- if you store an aiready categorized station under any other index name
- To display the frequency and index name of preset stations
- Receiving Broadcasts
- Recording an Audio Source
- 1
- Select the desired program source with the function selector. |
- 2 Set the tape (DAT) deck in the recording mode.
- 3 Start playback of the selected program source.
- Note on recording
- Monitoring the recorded sound
- 1 Insert the recorded tape into tape deck 1 (or the OAT deck).
- 2 Insert a blank tape into tape deck 2 and adjust the recording level.
- 3 Press TAPE 1 or DAT to select the deck for playback.
- With the STR-D990
- Select the playback VCR with EDIT VIDEO.
- Set the playback VCR to the playback mode.
- 4 Set the VCR 1 to the recording mode.
- — Video editing —
- To view the other video source(s) on the monitor TV during dubbing
- To listen to an audio program during video tape dubbing
- With the STR-D790
- Press VIDEO 2/LD.
- 2 Set VCR 2 to the playback mode.
- 3 Set the VCR 1 to the recording mode.
- To listen to an audio program during video tape dubbing
- To record a TV program
- With the STR-D990
- 1 Select the playback VCR with EDIT VIDEO.
- Set the playback VCR to the playback mode.
- 3 At the point where audio cjubblng starts, press the pause button on the playback VCR.
- Press EDIT AUDIO.
- Select the audio program source with the function selectors.
- 6 Releasethepausemodeof the playback VCR and set the VCR 1 to the recording mode.
- 7 Start playback of the selected audio program source.
- Editing a Video Source
- Getting Ready for Dolby Surround Sound
- Getting Ready for Dolby Surround Sound
- i POWER-»onI 14 2 6
- 1 Press SOUND nELOONfOFF to ON.
- 2 Press DOLBY SUR.
- Select a program source with the function selector and start playback.
- 4 Select the Dolby pro logic mode with the DOLBY PRO LOGIC MODE button according to your speaker system.
- Press T. TONE on the remote commander to set toon.
- Sequence of the test tone
- Adjusting the Surround Sound
- Sound Field Settings
- Sound Field Settings
- Specifications
- Specifications