Document Outline

• Foreword
• Safety
• Table of Contents
• Section 1 Introduction
  • 1.1 About This Manual
  • 1.2 About 700 Series Modules
  • 1.3 SDI-12 Sondes
  • 1.4 Memory to Store Monitoring Data
  • 1.5 Pump Requirements
• Section 2 Installation/Preparation
  • 2.1 Preparing the Sampler
    • 2.1.1 Installing the Distributor Shaft Extension
    • 2.1.2 Mounting the Controller
    • 2.1.3 Installing the Distributor Arm and Discharge Tube
  • 2.2 Installing Bottle Kits
    • 2.2.1 Installing Racks
    • 2.2.2 Removing Racks
    • 2.2.3 Installing Composite Bottles
  • 2.3 Suction Line
    • 2.3.1 Guidelines for Measuring and Cutting the Suction Line
    • 2.3.2 Attaching Suction Line to Pump Tube
  • 2.4 Strainers
    • 2.4.1 Alternative to Strainers
  • 2.5 How Does the Sampler Work?
    • 2.5.1 Measuring Sample Volume
  • 2.6 Installing the Sampler
    • 2.6.1 Tips for Routing Suction Line
    • 2.6.2 Intake Placement
    • 2.6.3 Positioning a Sampler
  • 2.7 Connecting External Instruments
    • 2.7.1 Flow Meter
    • 2.7.2 Rain Gauge Connector
  • 2.8 Locking the Sampler
  • 2.9 Servicing the Sampler
• Section 3 Getting Started
  • 3.1 Initial Operation
    • 3.1.1 Selecting a Language
  • 3.2 Using Menus and Entering Numbers
    • 3.2.1 Selecting Menu Options
    • 3.2.2 Entering Numbers
  • 3.3 Quick View Screens
    • 3.3.1 Paging Through Quick View Screens
    • 3.3.2 Changing Settings in a Quick View Screen
  • 3.4 Clock and Calendar
    • 3.4.1 Setting the Clock and Calendar
    • 3.4.2 Menu Screens: Clock Start Times
  • 3.5 Menu Screens: Site Descriptions and Program Names
  • 3.6 Messages
    • 3.6.1 Information Messages
    • 3.6.2 Help Notes
    • 3.6.3 Warning Messages
    • 3.6.4 Operation Messages
  • 3.7 Menu Trees
• Section 4 Standard Programming
  • 4.1 Switching Between Standard and Extended Modes
  • 4.2 Language Selection, Units of Length
  • 4.3 Programming Examples
  • 4.4 Pacing
    • 4.4.1 Trigger Pacing
  • 4.5 Distribution
    • 4.5.1 Sequential
    • 4.5.2 Bottles Per Sample
    • 4.5.3 Samples Per Bottle
    • 4.5.4 Composite
    • 4.5.5 Continuous Sampling
  • 4.6 Start Times
    • 4.6.1 How Do Start Times Work?
    • 4.6.2 Sampler Enable/Disable
  • 4.7 Running Programs
    • 4.7.1 Run Time Screens
    • 4.7.2 Module Readings
  • 4.8 Interrupting a Running Program
    • 4.8.1 Stop Program
    • 4.8.2 Resume Program
    • 4.8.3 View Data
    • 4.8.4 Grab Sample
    • 4.8.5 Pump Tube Alarm
    • 4.8.6 Calibrate Volume
    • 4.8.7 Cal/Adj Parameters
    • 4.8.8 Adjust Pacing
    • 4.8.9 Adjust Volume
    • 4.8.10 Power Used
  • 4.9 Other Functions
  • 4.10 Manual Functions
  • 4.11 Grab Samples
  • 4.12 Calibrate Volume
    • 4.12.1 Calibration Tips
  • 4.13 Operating the Pump
  • 4.14 Moving the Distributor Arm
  • 4.15 Reports
    • 4.15.1 Collecting Reports
    • 4.15.2 Viewing the Data
    • 4.15.3 Configuring Reports
    • 4.15.4 Sampling Results Report
    • 4.15.5 Combined Results Report
    • 4.15.6 Summary Report
  • 4.16 System IDs
  • 4.17 Programming for 700 Series Modules
• Section 5 Extended Programming
  • 5.1 Extended and Standard Mode
  • 5.2 One-Part and Two-Part Programs
  • 5.3 Storage for Extended Programs
    • 5.3.1 Selecting a Stored Program
  • 5.4 Programming for 700 series Modules
  • 5.5 Programming SDI-12 Sondes
  • 5.6 Programming Examples
    • 5.6.1 Storm Water Runoff Sampling
  • 5.7 Suction Head
  • 5.8 Rinses and Retries
  • 5.9 Pacing
    • 5.9.1 Event Pacing
    • 5.9.2 Event Paced Sampling
    • 5.9.3 Nonuniform Time Pacing
    • 5.9.4 Nonuniform Clock Time Pacing
    • 5.9.5 Nonuniform Interval Pacing
    • 5.9.6 Random Interval Pacing
  • 5.10 Distribution
    • 5.10.1 Sequential
    • 5.10.2 Bottles Per Sample
    • 5.10.3 Samples Per Bottle
    • 5.10.4 Composite
    • 5.10.5 Multiple Bottle Compositing
    • 5.10.6 Time Switching
    • 5.10.7 Continuous Sampling
  • 5.11 Flow Proportional Sample Volumes
    • 5.11.1 Calculating Variable Sample Volume Settings
    • 5.11.2 Calculations when Using an External Flow Meter
    • 5.11.3 Calculations when Using a 700 Series Flow Module
  • 5.12 Sampler Enable
    • 5.12.1 Sampler Enable
  • 5.13 Sampler Enable Responses
    • 5.13.1 Once Enabled Stay Enabled
    • 5.13.2 Repeatable Enable
    • 5.13.3 Sample at Enable or Disable
    • 5.13.4 Delay To Start Of Sampling
    • 5.13.5 “Dry Period” Option
    • 5.13.6 Resetting the Sample Interval at Enable
  • 5.14 Pauses/Resumes
  • 5.15 Running Programs
    • 5.15.1 Run Time Screens
    • 5.15.2 Interrupting a Running Program
  • 5.16 Sampling Reports
  • 5.17 Other Functions
  • 5.18 Software Options
    • 5.18.1 Liquid Detector Enable/Disable
    • 5.18.2 Programming Style
    • 5.18.3 Measurement Interval
    • 5.18.4 Dual Sampler Mode
    • 5.18.5 Pre-sample and Post-sample Purge Counts
    • 5.18.6 Serial Output
    • 5.18.7 Program Lock
  • 5.19 Hardware Setup
    • 5.19.1 SDI-12 Sonde Setup
    • 5.19.2 Rain Gauge Setup
    • 5.19.3 I/O Pin Programming
    • 5.19.4 Refrigerator Temperature
    • 5.19.5 Analog Output
    • 5.19.6 Dialout Alarms
    • 5.19.7 Pager Numbers
    • 5.19.8 Digital Modem Text Messaging
  • 5.20 Memory
  • 5.21 Pressurized Lines
  • 5.22 Command Driven Operation
  • 5.23 Command Driven Sampler Responses
• Section 6 SDI-12 Sondes
  • 6.1 SDI-12 Data Parameters
  • 6.2 Scanning For Sondes
  • 6.3 Teledyne Isco Ready Sondes
  • 6.4 Other SDI-12 Sondes
  • 6.5 Sonde Setup - Storing Parameter Data
  • 6.6 Sonde Calibration and Validation
    • 6.6.1 The Calibration Screens
    • 6.6.2 The Validation Screen
  • 6.7 Disconnecting Sondes
• Section 7 Remote Operation
  • 7.1 Computer Operation
    • 7.1.1 Menu Control
    • 7.1.2 External Program Control
    • 7.1.3 Remote Control of Sampler Keypad
  • 7.2 Telephone Commands
• Section 8 Maintenance
  • 8.1 Maintenance Checklist
  • 8.2 Cleaning Guidelines
    • 8.2.1 Refrigerator
    • 8.2.2 Controller
    • 8.2.3 Sample Bottles
    • 8.2.4 Suction Line, Pump Tube, and Discharge Tube
    • 8.2.5 Strainer
    • 8.2.6 Air Filter
    • 8.2.7 Condenser
  • 8.3 Cleaning Protocols for Priority Pollutants
    • 8.3.1 Teledyne Isco Glass Sample Bottles
    • 8.3.2 Vinyl Suction Line
    • 8.3.3 Teflon Suction Line
    • 8.3.4 Teledyne Isco Pump Tube
  • 8.4 Maintenance Screens
    • 8.4.1 Set Clock
    • 8.4.2 Pump Tube Alarm
    • 8.4.3 Internal Battery Warning
    • 8.4.4 Diagnostics
  • 8.5 Replacing the Pump Tube
  • 8.6 Opening the Controller Case
  • 8.7 Replacing the Desiccant
  • 8.8 Replacing the Internal Battery
  • 8.9 Error Messages
  • 8.10 Pump Tube Warning
  • 8.11 Servicing the Refrigerator
• Appendix A Menu Flowcharts
• Appendix B Material Safety Data Sheets
• Appendix C General Safety Procedures
  • C.1 Hazards
    • C.1.1 Adverse Atmosphere
    • C.1.2 Deteriorated Rungs
    • C.1.3 Traffic
    • C.1.4 Falling Objects
    • C.1.5 Sharp Edges
    • C.1.6 Lifting Injuries
  • C.2 Planning
  • C.3 Adverse Atmospheres
  • C.4 Entering Manholes
    • C.4.1 Traffic Protection
    • C.4.2 Removing the Covers
    • C.4.3 Other Precautions
    • C.4.4 Emergencies
    • C.4.5 Field Equipment
    • C.4.6 Lethal Atmospheres in Sewers
• Appendix D Replacement Parts
• Appendix E Accessories List
  • E.1 Order Information
  • E.2 Samplers
  • E.3 Bottle Kits
  • E.4 Bottle Racks, Retaining Rings, Discharge Tubes, Distributor Arm
  • E.5 Bulk Sets of Bottles with Lids
  • E.6 Pump Tubes, Suction Line, Strainers
  • E.7 Data Collection Devices and Cables
  • E.8 12-Volt Power Sources
  • E.9 Modules, Rain Gauges, & Interfacing Instruments
  • E.10 SDI-12 Data Acquisition Connect Cables
• Index
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • V
  • W
  • Y
• Warranty