Document Outline

• Getting Started
• Other Information
• Appendix
  • Figure: 1 Package Contents 2
  • Figure: 2 ViewSonic PJ700 Projector 3
  • Figure: 3 System Setup 5
  • Figure: 4 Recommended Projector Distances 6
  • Figure: 5 Angle Adjustment 7
  • Figure: 6 Projector and Remote Controls 8
  • Figure: 7 Lamp Replacement 20
  • Figure: 8 Installing the Batteries 21
  • Figure: 9 Attaching the Handle 22
  • For Your Records
• Getting Started
  • Package Contents
    • Figure 1: Package Contents
  • Important Safety Warnings
  • Projector Components
    • Figure 2: ViewSonic PJ700 Projector
  • Setting up the Projector
    • 1 Connect the Power Cord and Input/Output Devices.
    • 2 Remove the lens cap.
    • 3 Turn on the Projector.
    • 4 Press the Standby/On button.
    • 5 Position the Projector.
    • 6 Turn on the Input Devices and select the Input Signal.
    • 7 Adjust the image size.
    • 8 Adjust the Focus.
    • 9 Adjust the Keystone Control.
    • Connecting Input and Output Devices
      • Figure 3: System Setup
    • Positioning the Projector
      • Figure 4: Recommended Projector Distances
      • Table 1: Recommended Distances to Screen
    • Adjusting the Projector Angle
      • 1 Press the release button to lower the front foot, then tilt the projector up as shown in Figure...
      • 2 Release the button to lock the front foot in place.
      • 3 Rotate the rear foot adjuster to align the image.
        • Figure 5: Angle Adjustment
    • Using The Projector
      • Figure 6: Projector and Remote Controls
  • Control Buttons
    • Standby/On Button
    • The projector cannot be restarted within 60 seconds after it is turned off because the projector ...
    • Input Button (Video and RGB Buttons)
    • Menu Button
      • 1 Use the left or right arrow buttons to select a menu (Setup, Input, Image, Options).
      • 2 Use the up and down arrow buttons to highlight an item on the displayed menu.
      • 3 Use the right arrow button to select the highlighted menu item.
      • 4 Use the arrow buttons as indicated on screen to adjust the menu item.
    • Menu Select Button
    • Position Button
    • Magnify Buttons
    • Reset Button
    • Volume Buttons
    • Mute Button
    • Blank Button
    • Freeze Button
    • Timer Button
    • Auto Button
  • OnView Menus
    • 1 Press the MENU button on the remote control or the projector control pad to display the OnView ...
    • 2 Use the left or right arrow buttons to select a menu (Setup, Input, Image, Options).
    • 3 Use the up and down arrow buttons to highlight an item on the displayed menu.
    • 4 Use the right arrow button to select the highlighted menu item.
    • 5 Use the arrow buttons as indicated on screen to adjust the menu item.
    • Setup Main Menu
    • Input Menu
    • Image Menu
    • Options Menu
    • No Signal Menu
• Other Information
  • Specifications
    • Timing Chart
      • Table 2: Computer Signal Rates and Resolution
  • Troubleshooting
    • Power Indicator Lights
      • Table 3: Power Indicator Lights
    • Screen Messages
      • Table 4: Screen Messages 
  • Maintenance
    • Projector Lamp
      • Figure 7: Lamp Replacement
      • 1 Gently turn the projector over and place it on a towel or blanket. Expose the lamp cover on the...
      • 2 Loosen the lamp cover screw as shown.
      • 3 Gently remove the cover.
      • 4 Loosen the lamp unit screws (after the cover is removed).
      • 5 Gently pull the unit out of the lamp compartment using the flip- up handle grip.
      • 6 Gently insert the new lamp.
      • 7 Replace the lamp unit screws.
      • 8 Replace the cover and secure with the lamp cover screw.
      • 1 Press (and hold for three seconds) the Reset button on the projector control pad. The “Lamp hou...
      • 2 Press the Reset button on the projector control pad while the lamp timer is displayed.
      • 3 Use the direction arrows to select zero (0) and wait until the Lamp timer display clears.
    • Remote Control Battery
      • Figure 8: Installing the Batteries
      • 1 Pull the plastic tab from the battery access door when using the new projector for the first time.
      • 2 Push the tab on the bottom of the remote unit and remove the battery cover.
      • 3 Gently remove the battery from the holder and replace it with a new battery.
      • 4 Ensure that the positive and negative terminals (+ / -) are positioned correctly.
      • 5 Push the battery and holder back into the battery slot. The holder should click into place.
    • Cleaning Instructions
      • 1 Make sure the projector is cool and the power cord is unplugged before beginning.
      • 2 Vacuum the air-filter.
    • Attaching the Optional Handle
      • Figure 9: Attaching the Handle
      • 1 Lift one handle hook on the side of the projector.
      • 2 Pass one end of the handle through the handle hook.
      • 3 Buckle the end of the handle as shown.
      • 4 Repeat steps 1 through 3 to attach the other end of the handle.
  • Customer Support
  • Limited Warranty
    • VIEWSONIC Projector
      • 1. Any product on which the serial number has been defaced, modified or removed.
      • 2. Damage, deterioration or malfunction resulting from:
        • a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized produ...
        • b. Repair or attempted repair by anyone not authorized by ViewSonic.
        • c. Any damage of the product due to shipment.
        • d. Removal or installation of the product.
        • e. Causes external to the product, such as electric power fluctuations or failure.
        • f. Use of supplies or parts not meeting ViewSonic’s specifications.
        • g. Normal wear and tear.
        • h. Any other cause which does not relate to a product defect.
      • 3. Removal, installation, and set-up service charges.
      • 1. For information about receiving service under warranty, contact ViewSonic Customer Support. Yo...
      • 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip...
      • 3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic ...
      • 4. For additional information or the name of the nearest ViewSonic service center, contact ViewSo...
      • 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENC...
      • 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
      • 3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
• Appendix
  • Power Cord Safety Guidelines
  • FCC Information