Genie SILENTMAX 1000 - Manual (Page 8)

7 ©2011 The Genie Company 9/2011
IntelliCode® 1 or 2 wireless keypad
Door moves.
(To verify memory is cleared—try to operate the garage door
using one of your remote devices. The opener should
not respond.)
Both LEDs OFF confirms communication
is established with operator.
Round LED BLUE then OFF, Long LED FLASHING PROGRAM
SET
Press & hold
2 seconds.
Release.
ACTION LED INDICATION/RESULT
BLUE
OFF
OFF
OFF
OFF
OFF
BOTH BLUE
FLASHING
Release.
OFF
PURPLE
FLASHING
Clearing remotes from powerhead memory will
clear ALL programmed remotes and wireless
keypad. NOTE:
All remotes and wireless keypads
must be reprogrammed.
Your door opener will no longer recognize any
signal received from a missing remote.
Press & hold
BOTH open
and close
buttons
together.
REMOTE CLEARED FOR REPROGRAMMING
LOST OR STOLEN REMOTE - CLEARING MEMORY
OPTIONAL PROGRAMMING
1
2
3
Enter your PIN
on the wireless keypad.
OFF
BLUE OFF
Press & release 2 times.
Press &
release
ACTION LED INDICATION/RESULT
Genie® Intellicode® 2 Wireless Keypad comes
with a complete set of instructions.
Independent Light Control Button
Controls door opener lights from inside garage
Sure-Lock™ Button
r e t f a s l o r t n o c s e l b a s i d K C O L –
. d e s o l c y l e t e l p m o c s i r o o d
– UNLOCK allows controls to
work
normally
Indicator Light
Red indicator light is always ON
When Sure-Lock™ is ON the
indicator light flashes
Open/Close Button
Open and closes door from inside garage.
WALL CONSOLE - OVERVIEW
Use only the Series III wall console provided with this unit.
Wall console has three buttons and one indicator light.
Indicator Light
Indicator light will display Red when wall console is
properly wired and Sure-Lock
™ is OFF. When Sure
is ON indica
Lock ™
tor light flashes.
Open/Close Button
Use this button to open or close garage door. When
Sure-Lock™ is ON the Open/Close button will CLOSE
door only. Note: Constant button pressure in the
CLOSE mode will override error responses in the
powerhead and close door.
Independent Light Control Button
Use this button to turn powerhead lights ON.
Powerhead lighting will remain ON until this button
is pressed again or a door action has been completed.
Note: If opener has a Motion Detector sensor, it will
keep powerhead lights ON as long as motion is detected
Sure-Lock™ Button
When Sure-Lock™ is ON the powerhead cannot be
activated by the wall console or a remote.
s Press and hold for 5 seconds (or until Indicator
Light flashes) to activate Sure-Lock™.
s Press and release to turn Sure-Lock™ OFF.
Tip: If the Wall Console is energized (LED ON), but the
door does not
respond to the
OPEN/CLOSE
button-verify
the Console is
wired to the
BWC terminals
on the powerhead.
STB BWC IWC
NOT
USED
NOT
USED
NOT
USED
NOT
USED
FROM STBs
FROM WALL
CONSOLE
STB BWC IWC
FROM STBs
FROM WALL
This opener has a Serial Number sticker in which the serial
numbers begin with 10 or higher.
MODEL AC SR3 THE GENIE COMPANY
FCC ID: B8Q AC SR3 Residential Door Operator
IC: 2133A-CSD1D 120V. 60HZ. 5A
FOR H LP CAL 1-800-35GENIE OR WWW.GENIECOMPANY.COM
S/N:10XXXX XXXXXXX
Wall consoles from other manufacturers may not work with
openers of these serial number groups. Genie® Series I wall
buttons and Series II wall consoles will not work with openers
of this serial number group.
ROGRAM
SET
Press & Hold for
2 seconds or until
round LED turns blue
then OFF.
Then Long LED flashes purple .
1
2
4
5
PURPLE
FLASHING
CONSOLE