Document Outline

• Data Projector
• LVP-XD10U
• LVP-SD10U
  • Copyright
  • Disclaimer
  • Warning
  • COMPLIANCE NOTICE
  • Caution
  • Safety Instructions
    • 1. Read all of these instructions before you operate your projector and save them for future refe...
    • 2. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately...
    • 3. Power is still available when the projector is in the standby mode. Never replace the lamp ass...
    • 4. Do not attempt to service this product yourself, as opening or removing the covers may damage ...
    • 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing ...
    • 6. The Standard Remote Control contains a low-power laser that acts as a pointing device during p...
    • 7. This product is capable of displaying inverted images for ceiling mount configurations. Please...
    • 8. Openings in the front or at the two sides are for ventilation. They must not be blocked or cov...
    • 9. For ventilation reasons, the fan continues to operate for about 1 minute after the projector h...
    • 10. Do not look straight at the projector lens during operation. The intense light beam may injur...
• Outline
• Table of Contents
  • 1. Turn the main power switch off and disconnect the power cord from the outlet.
  • 2. Remove the lamp cover.
  • 3. Loosen the 2 screws and pull the handle to remove the lamp.
  • 4. Replace the lamp with a new one and fix it using the same screw.
  • 5. Install the lamp cover and fix it using a screw.
  • Introduction
    • Projector Features
• A Image Resolution
• B Brightness
• C Portability
• D Keystone
• E Multilanguage
• F Auto Detect System
• G Ceiling Mount and Rear Screen Projection
• H AV box (Model name: VA-10U)
  • Description
• A FRONT (figure)
• B REAR (figure)
• C BOTTOM (figure)
  • Installation
• A Positioning
• B Adjustable Feet
  • Moving the Projector
  • Accessories
  • Connection
• A Connecting the Projector to Computer/Notebook
  • Operation
    • Turn On/Off Procedure
• A Power on
• B Standby
  • External Control
• A Control Pad
• MAIN UNIT
• FUNCTION
• MAIN UNIT
• FUNCTION
  • B Remote Control
• Main Unit
• Function
  • Inserting Batteries in the Remote Control
    • Usage and Replacement of Lamp
  • A Lamp/temperature Status LED Indicator
    • 1. Lamp in excess of service hours
      • 1. "PLEASE CHANGE A NEW LAMP. AND RESET THE LAMP TIMER" will be displayed on the screen if the la...
      • 2. "PLEASE CHANGE A NEW LAMP. THE POWER WILL TURN OFF AFTER 20 HOURS" will be displayed on the sc...
      • 3. "PLEASE CHANGE A NEW LAMP" will blink on the screen together with a green LED if the lamp has ...
    • 2. Lamp is not well attached
    • 3. Temperature is too high
    • 4. Normal status
  • B Replacing the Lamp
    • Replacing the lamp
    • Resetting Lamp Timer
• OSD
• FUNCTION
• OSD
• FUNCTION
  • OSD
  • A Display Page
• Setting effects
  • B Image Page
• Setting effects
  • C Control Page
• Setting effects
  • D Source Page
    • Other Correspondent Remote Functions and Messages
• OSD
• FUNCTION
  • Maintenance and Troubleshooting
  • A Lamp Replacement
  • B Cleaning the Lens
    • 1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth (abrasive cleaners, sol...
    • 2. Avoid using an excessive amount of cleaner.
    • 3. Lightly wipe the clean cloth over the lens.
    • 4. Affix the lens cover whenever the projector is not in use.
  • C Troubleshooting
• PROBLEMS
• TRY THESE SOLUTIONS
  • Specifications
  • A Optical
  • B Electrical
  • C Mechanical
  • D Preset Display Resolution Table
  • Appendix
  • Features and Connection
    • AV Connection Port
    • AV Control Pad
    • Connecting the Box