Marantz DV-12S1 - Manual (Page 35)

35
ENGLISH
Adjust the output level from
the speakers (Gain setting)
This setting should be made when the AUDIO OUT
(5.1 channel) jacks on the rear panel are connected to
an AV amplifier or receiver. The output level of each
speaker in your system can be set and confirmed. The
factory setting is set to
[Fix] . However, when you want
to adjust the output level, select [Variable] .
Settings: Fix*
Variable
* Factory setting
When "Variable" is selected
1
Move the cursor control joystic up or down to
select the speaker.
Speakers set to [Off] in the [Speaker Setting] setting
cannot be selected.
2
Move the cursor control joystick right or left to
set the output level.
The value can be adjusted in the range of -6.0 dB to 6.0
dB in 0.5 dB increments. The output level of front L/R
speakers are fixed and therefore cannot be adjusted.
3
Repeat steps 1 and 2 for each speaker in your
system.
Set to Test tone
You can’t use the Test Tone function when the [Audio
Out] setting is [2 Channel] (page 33).
The Test Tone will not work with the disc tray open, or
while a disc is playing.
4
Move the cursor control joystic up to select
[Gain Setting] and press cursor control joystic
right.
5
Move the cursor control joystic up or down to
select the speaker.
Off : Test tone is not output. (Factory Setting)
On : Test tone output is manually controlled.
Auto : Test tone is automatically output.
Audio Out – 5.1 Channel
Speaker Setting
Gain Setting
CD Digital Direct – Off
Audio DRC – Off
Move Exit
Fix
Variable
SETUP
Audio1 Audio2 General Language Video
Audio1 Audio2 General Language Video
SETUP Exit ENTER Select
L
C
R
RS
LS
SW Return
Gain Setting
— 0.0 dB
–2.0 dB
— 0.0 dB
— 0.0 dB
— 0.0 dB
— 0.0 dB
Move
L R
SW
LS RS
Audio1 Audio2 General Language Video
SETUP Exit ENTER Select
L
C
R
RS
LS
SW Return
Test Tone
Move
— On
— Off
— Off
— Off
— Off
— Off
L R
SW
LS RS
When "On" is selected
Move the cursor control joystick up to the speaker
selection line, then Move the cursor control joystick right
or left to select the speaker to output the test tone from.
The test tone is output from the selected speaker. To
output the test tone from another speaker, change the
speaker selection.
When "Auto" is selected
Test tone is output in the following order.
(Front) Left, Center, (Front) Right, Surround Right,
Surround Left, (Front) Left, ...
6
Move the cursor control joystic up to select
[Test Tone] and press cursor control joystic
left.
This takes you back to the Gain Setting screen.
7
Move the cursor control joystick up or down to
select the speaker, then move the cursor
control joystick right or left to adjust the output
level while listening to the test tone.
To stop the test tone
Move the cursor control joystick down to the "Test Tone"
setting, then move the cursor control joystick right or left to
select
[Off] in the [Test Tone] setting.
Notes
• When [Variable] is selected, the output level of all speakers is
uniformly set to –6.0 dB. The output level of each speaker
(center, surround, or sub woofer) can then be adjusted in the
range of –6.0 dB to 6.0 dB. "6.0 dB" is the maximum level of
[Variable] and also the level set for [Fix] . Therefore, when
[Variable] is selected, the output level will usually be lower than
when the setting is set to [Fix] .
• The [Variable] setting has no effect on CD and Video CD
playback.
• The test tone is not output when the setting is set to [2 Channel]
in the [Audio Output] setting (page 33), while the disc tray
opens, or while a disc is playing.
Audio Out – 2 channel
Speaker Setting
Gain Setting – Fix
CD Digital Direct
Audio DRC – Off
Move Exit
On
Off
SETUP
Audio1 Audio2 General Language Video
Listening to higher quality CD
sound (CD Digital Direct)
By setting the [CD Digital Direct] setting to [On] , internal
circuitry unrelated to CD playback can be bypassed to
produce a higher quality CD sound.
Settings: On (Bypass unnecessary circuitry for CD
playback.)
Off (Passes through the necessary circuitry for
DTS CD playback.)
* Factory setting
Note
If this setting is set to [On] when a DTS CD is played back, noise is
produced.
Audio Out – 2 channel
Speaker Setting
Gain Setting – Fix
CD Digital Direct
Audio DRC – Off
Move Exit
On
Off
SETUP
Audio1 Audio2 General Language Video
By setting the [CD Digital Direct] setting to [On] , internal
circuitry unrelated to CD playback can be bypassed to
produce a higher quality CD sound.
Settings: On (Bypass unnecessary circuitry for CD
playback.)
Off* (Passes through the necessary circuitry for
DTS CD playback.)
* Factory setting
Note
If this setting is set to [On] when a DTS CD is played back, noise is
produced.
ADJUSTING A
UDIO AND
VIDEO SETTINGS