Marantz DV-12S1 - Manual (Page 65)

65
ENGLISH
Settings are canceled.
When the power is cut due to by power failure or by
unplugging the power cord, settings will be canceled.
\ Before unplugging the power cord, press
POWER button on the Remote Control and checking
that STANDBY indicator light in the display, then press
POWER on the front panel to turn the player off.
No picture.
Connection is incorrect.
\ Check that cord connections are correct and that plugs
are firmly connected.
Operation (settings) of TV or AV amplifier is not
appropriate.
\ Be sure that your TV, receiver, or amplifier is set up to
view DVD playback.
\ Check that VIDEO ON/OFF switch is set to the correct
position (page 61).
The screen is stretched or aspect does not change.
The multi aspect setting is not appropriate.
\ Change the aspect setting in the
[TV Screen] setting in
the Setup screen Video menu to the screen type most
appropriate to the TV or monitor you are using (page
36).
The screen is suddenly squeezed when the Setup screen
is opened.
If the Setup screen is opened during playback of a DVD
being viewed in the letter box format, the screen may
switch to the wide screen format.
\ This is not a malfunction. The screen will return to
normal when the Setup screen is closed.
Picture disturbance during playback or dark.
This is not a malfunction.
\ This player is compatible with Macro-Vision System
copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
stripes etc., may appear on some sections of the
picture depending on the TV.
When using a component video connection, if progressive
scan output is selected with a TV that is not compatible
with progressive scan video, you will not be able to see any
picture. To, remedy this, do one of the following:
\ Set the FL menu setting
“COMP VIDEO” to
INTERLACE (page 24).
When recorded on a VCR or passed through an AV
selector, there is disturbance in the playback picture.
This is not a malfunction.
\ Due to the player’s copy protection circuits, connection
of this device through a VCR or an AV selector may
prevent recording or cause picture problems.
Remote control operation is not possible.
The rear panel control input jack on the player is being
used.
\ Check that
REMOTE CONTROL SW is set to the
external position (page 19).
The remote control is too far from the player, or the angle
with the remote sensor is too wide.
\ Be sure to operate the remote from a location within its
operating range (page 9).
The batteries are exhausted.
\ Replace the exhausted batteries with all new batteries
(page 9).
\ Check that REMOTE CODE setting is set to the correct
position (page 13, 24).
Audio is not output or is distorted.
The Setup screen Audio 1 menu [Linear PCM Out]
setting is set to [Down Sample On] . Digital output is
prohibited on some discs.
\ Be sure to make analog audio connections as well as
digital connections (page 15-18).
The disc is dirty.
\ Refer to
‘Disc Care’ (page 63).
The connection plugs are not inserted fully into the
terminals or are not connected.
\ Check that all connection plugs are firmly inserted.
The connection plug or terminal is dirty.
\ Check that the plugs and terminals are wiped clean of
dirt, etc.
Audio cable connection is wrong.
\ Check to make sure that the audio cables are
connected correctly (page 15-18).
Connection is made to the stereo amplifier‘s PHONO input
terminal.
\ Change connection to any input terminal except
PHONO.
The pause mode is engaged.
\ Press
PLAY 3 to exit the pause mode.
Stereo amplifier operation is incorrect.
\ Check input (CD, AUX, etc.) selector to determine if it
is selected for DVD playback.
Noticeable difference in DVD and CD volume.
DVDs and CDs use different recording methods.
\ This is not a malfunction.
\ When playing DVDs with the Gain Setting set to
[Variable] , the overall volume may seem lower than on
the [Fix] setting.
Audio mix does not sound right or sounds incomplete
(for example, the dialog of the actors cannot be heard).
Audio output selection is incorrect.
\ When [5.1 Channel] is selected, Dialog is not output
from the front left and right speakers. When [2 Channel]
is selected, sound is only output through the front left
and right speakers.
Caution
Static electricity or other external influence may cause
malfunctioning of this unit. In this case, unplugging the
power cord and then re-plugging it in will usually reset the
unit for proper operation. If this does not correct the
problem, please consult your nearest MARANTZ service
center.
ADDITIONAL INFORMA
TION