Multi-Tech Systems MT4X56USB - Manual (Page 83)

Glossary
MT4X56USB 83
Digital Signal: A discrete or discontinuous signal (e.g., a sequence of voltage pulses). Digital devices, such as terminals
and computers, transmit data as a series of electrical pulses which have discrete jumps rather than gradual changes.
Digital Signaling Rates (DSn): A hierarchical system for transmission rates, where “DS0” is 64 Kbps (equivalent to ISDN B
channel), and DS1 is 1.5 Mbps (equivalent to ISDN PRI).
Digital Transmission: A method of electronic information transmission common between computers and other digital
devices. Analog signals are waveforms: a combination of many possible voltages. A computer’s digital signal may be only
“high” or “low” at any given time. Therefore, digital signals may be “cleaned up” (noise and distortion removed) and
amplified during transmission.
Digitize: To convert an analog signal to a digital signal.
DIP switch (pronounced “dip switch”): A set of tiny toggle switches, built into a DIP (dual in-line package), used for
setting configurable parameters on a PCB (printed circuit board).
Downstream: The direction of data flow from the host or away from the host. A downstream port is the port on a hub
electrically farthest from the host that generates downstream data traffic from the hub. Downstream ports receive upstream
data traffic.
Driver: When referring to hardware, an I/O pad that drives an external load. When referring to software, a program
responsible for interfacing to a hardware device; that is, a device driver.
Drop and Insert: The process where a portion of information carried in a transmission system is demodulated (“Dropped”)
at an intermediate point and different information is included (“Inserted”) for subsequent transmission.
DTE (Data Terminal Equipment): A term used to include any device in a network which generates, stores or displays user
information. DTE is a telecommunications term which usually refers to PCs, terminals, printers, etc.
DTMF (Dual-Tone MultiFrequency): A generic push-button concept made popular by AT&T TouchTone.
DWORD: Double word. A data element that is 2 words, 4 bytes, or 32 bits in size.
Dynamic Insertion and Removal: the ability to attach and remove devices while the host is in operation.
E
E&M: A telephony trunking system used for either switch-to-switch, or switch-to-network, or computer/telephone system-to-
switch connection.
EIA: The Electronics Industries Association is a trade organization in Washington, DC that sets standards for use of its
member companies. (See RS-232, RS-422, RS530.)
Encapsulation: A technique used by network-layer protocols in which a layer adds header information to the protocol data
unit from the preceding layer. Also used in “enveloping” one protocol inside another for transmission. For example, IP inside
IPX.
End User: The user of a host.
Endpoint: See Device Endpoint.
Endpoint Address: The combination of a Device Address and an Endpoint Number on a Universal Serial Bus device.
Endpoint Number: A unique pipe endpoint on a Universal Serial Bus device.
Ethernet: A 10-megabit baseband local area network that allows multiple stations to access the transmission medium at will
without prior coordination, avoids contention by using carrier sense and deference, and resolves contention by using
collision detection and transmission. Ethernet uses carrier sense multiple access with collision detection (CSMA/CD).
Excess Zeros: A T1 error condition that is logged when more than 15 consecutive 0s or fewer than one 1 bit in 16 bits
occurs.
Exchange: A unit (public or private) that can consist of one or more central offices established to serve a specified area. An
exchange typically has a single rate of charges (tariffs) that has previously been approved by a regulatory group.
Exchange Area: A geographical area with a single uniform set of charges (tariffs), approved by a regulatory group, for
telephone services. Calls between any two points within an exchange area are local calls. See also “Digital PBX”, “PBX”.
Exchange Termination (ET): The carrier’s local exchange switch. Contrast with “Loop Termination - LT”.
Explicit Congestion Management: The method used in frame relay to notify the terminal equipment that the network is
overly busy. The use of FECN and BECN is called explicit congestion management. Some end-to-end protocols use FECN
or BECN, but usually not both options together. With this method, a congestion condition is identified and fixed before it
becomes critical. Contrast with “implicit congesion”.