MITSUBISHI ELECTRIC WD-62628 - Manual (Page 22)

22 Chapter 2. Connecting
Connecting External Devices and NetCommand
®
Setup
.PEFM
.73

.73
.PEFM
.73

.73
.PEFM
-JGFTUZMF ¥

.PEFM

"73
.PEFM
%53
.PEFM
73
.PEFM
43
.PEFM
749%
.PEFM
74959
.PEFM
349
.PEFM
453%&
.PEFM
397
.PEFM
397
%FWJDF
"VEJP
0VUQVU





UP
"7
3FDFJWFS
*OQVUT
CZ
/BNF
7$3 7$3
 7$3 7$3 7$3 7JEFP
 7JEFP
 7$3 7$35BQF
7$3
%73 7JEFP
 7JEFP
 7$3
 7$3

4BUFMMJUF
3FDFJWFS "VY $BCMF%#4 "69 $% 7JEFP
 7JEFP
 %44 $% 4"5 7JEFP
 57%#4 57%#4 %57-%
%7%
1MBZFS %7% %7% CVJMUJO
%7%7%1 %7% 7JEFP
 %7% -%4"5 %7%-% 7JEFP
 5"1&.% $% %7%
57
.POJUPS
0VUQVU

%JHJUBM
"VEJP
57 57 57 57%#4 7JEFP
 7JEFP
 57 %7%57 57 7JEFP
 %7%-% %7%-% $#-4"5
$IBSU


.JUTVCJTIJ



.JUTVCJTIJ








#PTF















%FOPO







*OUFHSB




,FOXPPE


.BSBOU[



1JPOFFS





1JPOFFS









3PUFM











4POZ









:BNBIB


:BNBIB

AV
Receiver
TV
Device to be
connected
stereo and/or digital
audio cables
video and stereo
audio cables
stereo and/or digital audio cables
*3
&NJUUFST

NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to
each device through IR emitters. Additionally, it can learn the remote control signals used by most audio video devices
not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video
(A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver
back panels match the NetCommand setup that is displayed on screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this
chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 45.
The following charts show which preset inputs you should use on the TV and A/V receiver.
Chart 1 shows the default TV inputs existing in NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.
Chart 1
NetCommand Default Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service ANT-1
Antenna/Cable (digital/analog) ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
Cable box COMPONENT-1
VCR Input-1
Satellite Receiver (SAT) Input-2
Camcorder Input-3 (on front panel)
DVD Player COMPONENT-2
PC HDMI-2
After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for
connecting each device, custom name devices, add devices not included in the presets above or delete devices no
longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on device
setup.