External devices and netcommand® setup, Connecting external devices and netcommand, Setup – MITSUBISHI ELECTRIC WD-62628 User Manual

Page 22: Chapter 2. connecting

Advertising
background image

22

Chapter 2. Connecting

Connecting External Devices and NetCommand

®

Setup

.PEFM

.73

.73

.PEFM

.73

.73

.PEFM

-JGFTUZMF ¥

.PEFM

"73

.PEFM

%53

.PEFM

73

.PEFM

43

.PEFM

749%

.PEFM

74959

.PEFM

349

.PEFM

453%&

.PEFM

397

.PEFM

397

%FWJDF"VEJP0VUQVUUP

"73FDFJWFS*OQVUTCZ/BNF

7$3

7$3

7$3

7$3

7$3

7JEFP

7JEFP

7$3

7$35BQF 7$3%73

7JEFP

7JEFP

7$3

7$3

4BUFMMJUF3FDFJWFS

"VY

$BCMF%#4

"69

$%

7JEFP

7JEFP

%44

$%

4"5

7JEFP

57%#4

57%#4

%57-%

%7%1MBZFS

%7%

%7%

CVJMUJO

%7%7%1

%7%

7JEFP

%7%

-%4"5

%7%-%

7JEFP

5"1&.%

$%

%7%

57.POJUPS0VUQVU
%JHJUBM"VEJP

57

57

57

57%#4

7JEFP

7JEFP

57

%7%57

57

7JEFP

%7%-%

%7%-% $#-4"5

$IBSU

.JUTVCJTIJ.JUTVCJTIJ#PTF%FOPO*OUFHSB,FOXPPE.BSBOU[1JPOFFS1JPOFFS3PUFM4POZ:BNBIB:BNBIB

AV

Receiver

TV

Device to be

connected

stereo and/or digital

audio cables

video and stereo

audio cables

stereo and/or digital audio cables

*3&NJUUFST

NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to
each device through IR emitters. Additionally, it can learn the remote control signals used by most audio video devices
not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video
(A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver
back panels match the NetCommand setup that is displayed on screen.

To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this

chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 45.

The following charts show which preset inputs you should use on the TV and A/V receiver.

Chart 1 shows the default TV inputs existing in NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.

Chart 1

NetCommand Default Device Audio and Video Outputs to TV Inputs

Cable for CableCARD™ Service

ANT-1

Antenna/Cable (digital/analog)

ANT-1 if primary viewing source,
ANT-2 if secondary viewing source

Cable box

COMPONENT-1

VCR

Input-1

Satellite Receiver (SAT)

Input-2

Camcorder

Input-3 (on front panel)

DVD Player

COMPONENT-2

PC

HDMI-2

After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for

connecting each device, custom name devices, add devices not included in the presets above or delete devices no

longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on device
setup.

Advertising