MITSUBISHI ELECTRIC WD-62628 - Manual (Page 27)

Chapter 2. Connecting 27
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
OUTPUT
AUDIO OUTPUT RECORD OUTPUT DVI Analog Audio
1 2 VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1 2
IEEE 1394 INPUT/ OUTPUT
Net Command
IR EMITTER ¸
'
,INK ¸

INPUT
PC - 60Hz VGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720
)46
$BCMF
#PY
CBDL
QBOFM
TFDUJPO 

*/
065
065
580
8
" :
41-*55&3
*/
065
*ODPNJOH

$BCMF
3'
4QMJUUFS

7$3
CBDL
QBOFM






C




B
B
*G
ZPVS
7$3
IBT
B

WJEFP
DIBOOFM
PS
3'

0/0''
TXJUDI

TFU
JU

UP
0''
"UUBDI
POMZ
POF
WJEFP

DBCMF
UZQF
TUFQ




4WJEFP
SFDPNNFOEFE

JG
BWBJMBCMF C
VCR to a Cable Box (Audio & Video)
Figure 6
A two-way RF splitter, 4 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV but are available at most electronics
stores.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the cable box back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® feature.
4. Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.
5. Connect one coaxial cable from ANTENNA OUT on
the VCR back panel to ANT-2 AUX on the TV back
panel (optional).
6. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT-1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white cable
Figure 6. Connecting a VCR to a Cable Box
Note: NetCommand®
will assume your VCR
is connected to inputs
as shown on this page.
If you use any other
inputs for your VCR or
add a second VCR, this
change must match
in the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.
Connecting a VCR to a Cable Box (Audio & Video)
connects to the L (left) channel. If your VCR is mono
(non-stereo), connect only the white (left) cable.
7. Connect either an S-Video or composite video cable
from VIDEO OUT on the VCR back panel to INPUT 1
VIDEO on the TV back panel. Connect only one type
of video cable. S-Video is recommended, if available.
8. For NetCommand®-controlled recordings (including
TV Guide On Screen)
a. Connect a set of audio cables from AUDIO IN on
the VCR back panel to RECORD OUTPUT/AUDIO-
LEFT (MONO) and AUDIO-RIGHT on the TV back
panel. The red cable connects to the R (right)
channel and the white cable connects to the L
(left) channel.
b. Connect a video cable from VIDEO IN on the VCR
back panel to RECORD OUTPUT/VIDEO on the
TV back panel.
Note: With this connection configuration, it is
possible to view live cable programs through the VCR.
For best picture quality, however, always view live
cable programs directly from the cable box instead of
the VCR.