JVC BD-X200U - Manual (Page 37)

67
IN POINT OUT POINT
TC INPUT
EXIT
REMOTE CONTROL SCREEN ( DV SLAVE )
1 :
4
7
h : m : s f 2 :
5
8 3
6
9 h : m : s f : h : m : s f
CHAPTER MANUAL
BITRATE 8.0 Mbps DISC REMAIN 000 min
: : :
EDL LOAD
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:00:00:00
00:25:00:00
00:40:00:00 00:15:00:00
00:30:00:00
00:45:00:00 00:20:00:00
00:35:00:00
00:50:00:00
00:10:00:00
ADJUST
3. Starting the Record Process
Ⅵ Use the non-linear editor to control the DVD recorder.
● Each recording will be stored on the disc as a single title.
● Recording of video and audio to the DVD will be carried out from the In Point to the Out Point with chapters being automatically
created as specified.
Setting the Optimum Bit Rate
ADJUST can be used to set the optimum bit rate (i.e., the amount of data per
second) for the remaining space on a disc based on the recording time (or duration)
between the In Point and the Out Point.
● DISC REMAIN displays an estimate of the available space for recording on the
current disc.
● BIT RATE displays the current bit-rate setting.
To set the bit rate that best suits the remaining disc capacity, select ADJUST and
then press the SET button.
4. Ending the Record Process
Notes
● If no In Point has been set, recording will start in response to DV commands; however, since time codes are set for chapter
marks as relative values with respect to the In Point, chapters may not be created as intended. It is recommended, therefore,
that an In Point always be specified when chapters are to be created.
● When the chapter auto-create function is used, chapters will be created at specific intervals.
IN POINT OUT POINT
TC INPUT
EXIT REMOTE CONTROL SCREEN ( DV SLAVE )
1 :
4
7
h : m : s f 2 :
5
8 3
6
9 h : m : s f : h : m : s f
CHAPTER MANUAL
BITRATE 8.0 Mbps DISC REMAIN 000 min
: : :
EDL LOAD
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:00:00:00
00:25:00:00
00:40:00:00 00:15:00:00
00:30:00:00
00:45:00:00 00:20:00:00
00:35:00:00
00:50:00:00
00:10:00:00
FINALIZE
Ⅵ If you intend to play the recorded disc on this DVD recorder or on another player,
select FINALIZE and press the SET button.
Once finalizing has been carried out, no addition recordings can be made on
the disc.
Ⅵ To remove the recorded disc from your BD-X200, press the OPEN/CLOSE button
on the front panel.
68
Synchronous Recording
In, Out & Chapter Points from External Edit Lists
When dubbing a tape edited using an external VCR or non-linear editor to a DVD, the edit list (or EDL) created during the editing
process can be used to automatically set the In Point, Out Point, and chapter marks.
1. Transfer the external edit list to your BD-X200.
2. Select EDL LOAD from the REMOTE CONTROL screen and press
the SET button.
● The In Point, Out Point, and chapter marks are set in accordance with the
EDL.
IN POINT OUT POINT
TC INPUT
EXIT
REMOTE CONTROL SCREEN ( 9PIN MASTER )
1
:
4
7
h : m : s f
2
:
5
8
3
6
9
h : m : s f : h : m : s f
CHAPTER MANUAL
BITRATE 8.0 Mbps DISC REMAIN 000 min
: : :
EDL LOAD
EDIT/END TC SET
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:00:00:00
00:25:00:00
00:40:00:00 00:15:00:00
00:30:00:00
00:45:00:00 00:20:00:00
00:35:00:00
00:50:00:00
00:10:00:00
EDL LOAD
IN POINT OUT POINT
TC INPUT
EXIT
REMOTE CONTROL SCREEN ( 9PIN MASTER )
1
:
4
7
h : m : s f
2
:
5
8
3
6
9
h : m : s f : h : m : s f
CHAPTER MANUAL
BITRATE 8.0 Mbps DISC REMAIN 000 min
: : :
EDL LOAD
EDIT/END TC SET
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:10:00:00
00:40:00:00 00:20:00:00
00:50:00:00 00:30:00:00
01:10:00:00
: : :
: : : : : : : : :
JVC CSV
IN POINT
OUT POINT
Chapter1
Chapter2
Chapter3
Chapter4
Chapter5
00:00:00:00
01:00:00:00
00:10:00:00
00:20:00:00
00:30:00:00
00:40:00:00
00:50:00:00
Ⅵ Example 1: Loading a CSV-format EDL
EDL LOAD
EDIT RECORDER-IN RECORDER-OUT
0001 00:00:00:00 00:10:00:00
00:10:00:00 00:20:00:00
00:20:00:00 00:20:00:00
0002
0002
0003 00:30:00:00 00:40:00:00
00:40:00:00 00:50:00:00
00:40:00:00 00:50:00:00
0004
0004
00:50:00:00 01:00:00:00
00:50:05:00 01:00:00:00
0005
0005
IN POINT OUT POINT
TC INPUT
EXIT
REMOTE CONTROL SCREEN ( 9PIN MASTER )
1
:
4
7
h : m : s f
2
:
5
8
3
6
9
h : m : s f : h : m : s f
CHAPTER MANUAL
BITRATE 8.0 Mbps DISC REMAIN 000 min
: : :
EDL LOAD
EDIT/END TC SET
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:10:00:00
00:40:00:00 00:20:00:00 00:30:00:00
00:50:00:00 00:50:05:00
01:00:00:00
: : : : : : : : :
Set as the In Point Set as chapter marks
Set as the
Out Point
Set as a
chapter mark Already set
EDL LOAD
Procedure
● Line returns at the end of each line.
● Maximum of 98 chapter marks.
● Framing mode determined by the character in front
of the frame field. (U-model only)
Period (.) : Drop frames
Colon (:) : Non-drop frames
Ⅵ Example 2: Loading a Sony9100-format EDL
Recorder-In and Recorder-Out time codes are read from the X-source and Y-source rows, and these are then set as the
In Point, Out Point, and chapter marks for editing.
Notes
● Loading of external edit lists is possible when CHAPTER CREATION from the RECORDER [2/2] MENU screen is set to
MANUAL.
● The framing mode for time codes (i.e. drop or non-drop) will be matched to that of the edit list. (U-model only)
● In order to be read, the EDL must be of CSV or Sony9100 format.
● The priority sequence for loading is CSV † Sony9100 † internally-made EDL.
● Chapter marks are inserted at GOP intervals (i.e., 15 frames). It will not be possible to insert chapter marks that are closer
together than this interval.