JVC BD-X200U - Manual (Page 42)

77
DISC MENU Screen
The following table identifies and describes the parameters that may be set using the DISC MENU screen.
Top half
: Appearance on monitor screen
Bottom half : Appearance on LCD display
[ ]
: Default setting
Parameter Possible settings Description
FINALIZE [CANCEL]
EXECUTE
FINAL [CAN]
EXE
DISC ERASE [CANCEL]
EXECUTE
ERASE [CAN]
EXE
MENU
This parameter indicates whether or not the recorded disc is to be finalized. If a disc
recorded using this DVD recorder is to be played on a DVD player, it must first be
finalized. Once finalizing has been carried out, no addition recordings can be made
on the disc.
CANCEL
: Finalizing is not to be carried out.
EXECUTE : Finalizing is to be carried out.
It will be necessary to close all titles on a disc before it can be finalized.
* A maximum of 20 minutes will be required to complete finalizing.
This parameter indicates whether or not a DVD-RW (video mode) is to be erased.
CANCEL
: This disc is not to be erased.
EXECUTE : This disc is to be erased. In this process, all recorded data is erased
from the disc, and it can then be recorded to as a new disc.
This button is used to return to the Setup Menu screen.
INPUT SELECT MENU screen
The following table identifies and describes the parameters that may be set using the INPUT SELECT MENU screen.
Top half
: Appearance on monitor screen
Bottom half : Appearance on LCD display
[ ]
: Default setting
Parameter Possible settings Description
INPUT SELECT [LINE]
Y/C
DV
INPUT [LINE]
YC
DV
MENU
This parameter is used to select the audio and video input signals.
LINE : The composite video signal from the VIDEO LINE IN terminal and the analog
audio signals from the AUDIO IN terminals are to be used.
Y/C : The YC separate signal from the Y/C IN terminal and the analog audio signals
from the AUDIO IN terminals are to be used.
DV : The digital video and audio signals from the DV IN/OUT terminal are to be
used.
* The front-panel indicator corresponding to the type of input signal selected on this
screen will light up or start to flash.
Setting of this parameter will not be possible when REMOTE SELECT from the
REMOTE MENU screen has been set to DV(MASTER), DV(SLAVE), or
DV(TRIGGER). DV signals will be used for input at these times
This button is used to return to the Setup Menu screen.
78
Setup Menu
SYSTEM MENU Screen
The following table identifies and describes the parameters that may be set using the SYSTEM MENU screen.
Top half
: Appearance on monitor screen
Bottom half : Appearance on LCD display
[ ]
: Default setting
Parameter Possible settings Description
SET UP [OFF]
ON
(U-model only)
SETUP [OFF]
ON
(U-model only)
TEST SIGNAL [OFF]
ON
TEST S [OFF]
ON
FACTORY [CANCEL]
SETTING EXECUTE
FACTRY [CAN]
EXE
KEYBOARD [ENGLISH]
STYLE FRENCH
ITALIAN
GERMAN
SPANISH
JAPANESE
KBOARD [ENG]
FRN
ITL
GER
ESP
JPN
EDIT MENU [ENABLE]
DISABLE
EDIT [ON]
OFF
TOTAL RECORDING TIME —
— —
MENU
This parameter is used to indicate whether or not a setup signal is to be added to
analog video (i.e., composite or YC separate) during the recording process. The
actual setting depends on whether the input analog signal contains a setup signal.
OFF : This setting should be made when the input analog signal does not contain
a setup signal.
ON : This setting should be made when the input analog signal contains a setup
signal.
This parameter is used to indicate whether or not the color bar output by the DVD
recorder’s internal signal generator is to be displayed.
OFF : The color bar is not displayed and video from the VIDEO LINE IN terminal is
output to the monitor.
ON : The color bar is displayed. Use this setting when the color bar is to be
recorded.
This parameter is used to indicate whether or not all setup menu parameters are to
be returned to their default settings.
CANCEL
: Default settings are not to be restored.
EXECUTE : Default settings are to be restored.
This parameter is set when using a USB keyboard, and its purpose is to indicate the
keyboard’s layout (or language) as one of the following.
ENGLISH
FRENCH
ITALIAN
GERMAN
SPANISH
JAPANESE
Note
The system must be restarted after this parameter is changed.
This parameter is used to indicate whether or not a screen for editing the title and
chapter menus is to be displayed when title closing or finalizing is performed.
ENABLE : The menu editing screen is to be displayed.
Upon title closing, the THUMBNAIL EDIT screen will be displayed for
the corresponding chapter menu. (
☞ Page 47)
Upon finalizing, the TITLE MENU EDIT screen will be displayed for the
title menu. (
☞ Page 53)
DISABLE : The menu editing screen is not to be displayed.
This button displays the total time for recording and erasing operations. (xHour xxMin)
This button is used to retu4rn to the Setup Menu screen.