JVC DR-M10S - Manual (Page 82)

Filename [DR-M10SE_10Editing.fm]
Masterpage:Left+
82
EN
Page 82 February 12, 2004 5:23 pm
EDITING (cont.)
Output/Input Set
L-1 Output and L-1 Input Setting
(L-1 OUTPUT and L-1 INPUT)
The L-1 IN/OUT connector accepts and delivers either a
composite signal (regular video signal) or a Y/C signal (a signal
in which the luminance and chrominance signals are separated).
Set “L-1 OUTPUT” and “L-1 INPUT” to the appropriate mode
depending on the type of appliance connected to the unit’s L-1
IN/OUT connector.
A
Access the Main Menu screen.
Press SET UP.
B
Access the Output/Input Set screen.
C
Select the output or input mode for the L-1
IN/OUT connector.
(The boldface settings in the table below indicate the settings at
your purchase.)
D
Return to the normal screen.
Press SET UP.
NOTES:
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB”
or “COMPONENT”, it is not possible to set “L-1 INPUT” to
“S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is not possible to set
“L-1 INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is only possible to set
“L-1 OUTPUT” to “SCART VIDEO”.
● Component video signals are not output from the L-1 IN/OUT
connector.
● When Progressive scan mode is engaged, it is not possible to
select the setting of “L-1 OUTPUT”. (
੬
pg. 108)
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
A Press w e to move the
arrow to“FUNCTION SET
UP”, then press ENTER.
B Press w e to move the
arrow to “VIDEO IN/
OUT”, then press ENTER.
DVD TV
DVD
TIMER PROG/CHECK
NEXT PREVIOUS
PAUSE REC
REC MODE LIVE CHECK
SET UP DISPLAY ON SCREEN
OPEN/
CLOSE
SLOW SLOW PLAY/SELECT
STOP/ CLEAR
NAVIGATION TOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKL GHI MNO
TUV PQRS WXYZ
AUX CANCEL MEMO/MARK
DEF
CABLE/SAT
PR
SAT#
TV/CBL/SAT TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus+
rtwe
ENTER
SET UP
DVD TV
CABLE/SAT
A Press rt to move the
arrow to “L-1 OUTPUT”
or “L-1 INPUT”, then
press ENTER.
B Press rt to select the
appropriate setting, then
press ENTER.
8 L-1 OUTPUT
SCART VIDEO : If a connected appliance’s input is
compatible only with regular
video signals, set to “SCART
VIDEO”.
SCART S-VIDEO: If a connected appliance’s input is
compatible with Y/C signals, set to
“SCART S-VIDEO”. You can
obtain high-quality picture. (For
connection, be sure to use a 21-
pin SCART cable that is
compatible with the Y/C signal.)
SCART RGB : If a connected appliance’s input is
compatible with RGB signals, set
to “SCART RGB”. You can obtain
a high-quality RGB picture.
COMPONENT: If a connected appliance’s input is
compatible with Y/P
B
/P
R
signals,
set to “COMPONENT”. You can
obtain a high-quality Y/P
B
/P
R
picture. Switch the TV to the input
that you can watch component
video pictures.
8 L-1 INPUT
VIDEO : If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain a high-
quality picture. (For connection, be
sure to use a 21-pin SCART cable that
is compatible with the Y/C signal.)
DR-M10SE_01.book Page 82 Thursday, February 12, 2004 9:08 PM