JVC HR-XV48E - Manual (Page 54)

Filename [XV48EX_EN_10Subsidiary.fm]
Masterpage:Left+
54
EN
Page 54 October 9, 2004 10:34 pm
SUBSIDIARY SETTINGS (cont.)
8 POWER SAVE — ON / OFF
When this function is set to “ON,” you can reduce the power
consumption while the unit is turned off.
NOTES:
● During Power Save mode:
— the front display panel will be turned off.
— the Just Clock function (
੬
pg. 65) does not work.
— the picture may be distorted momentarily when you turn
on/off the unit.
● Power Save does not work when:
— the unit is in the timer mode.
— the unit’s power is turned off after timer-recording or Instant
Timer Recording.
— the Automatic Satellite Programme Recording mode is
engaged. (
੬
pg. 28)
— “L-2 SELECT” is set to “DECODER” or “SAT”. (
੬
pg. 54)
8 VIDEO STABILIZER — ON / OFF
When this function is set to “ON,” you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
NOTES:
● When you finish viewing a tape, be sure to set this function to
“OFF.”
● Regardless of the setting, this function has no effect during
recording and during special effects playback.
● The on-screen display may jitter vertically when this function
is set to “ON.”
● To watch recordings with close-caption, set this function to
“OFF.”
8 L-2 SELECT — A/V / DECODER / SAT
Set “L-2 SELECT” to the appropriate mode depending on the
type of appliance connected to the unit’s L-2 IN/DECODER
connector.
A/V : To use this unit as the recording deck with the player
connected to the L-2 IN/DECODER connector, or to use the
satellite receiver connected to the L-2 IN/DECODER
connector.
DECODER : To use a decoder connected to the L-2 IN/DECODER
connector.
SAT : To view a satellite programme with the TV set while the
unit is turned off. (
੬
pg. 50)
NOTES:
● If you have a satellite receiver or a decoder connected to the
L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back
to the appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the
L-2 IN/DECODER connector, leave “L-2 SELECT” set to “A/V.”
● When “L-2 SELECT” is set to “SAT,” “SAT” appears on the TV
screen or front display panel instead of “L-2.”
8 COLOUR SYSTEM — PAL/NTSC / MESECAM
You can play back PAL, NTSC and MESECAM tapes, or record
PAL and SECAM* signals on this unit. Select the appropriate
colour system.
* SECAM signals will be recorded as MESECAM on this unit;
MESECAM is the designation for tapes with SECAM signals that
have been recorded on a MESECAM-compatible PAL video
cassette recorder.
PAL/NTSC : To record PAL signals, or play back a PAL or NTSC
tape.
MESECAM : To record SECAM signals, or play back a MESECAM
tape.
NOTES:
About NTSC Playback
● Some TVs shrink the picture vertically and place black bars at
the top and bottom of the TV screen. This is not a malfunction
on the part of either the unit or the TV.
● The picture may roll up and down. This can be corrected using
the V-HOLD control found on some TVs. (This cannot be
corrected if the TV does not have a V-HOLD control.)
● The counter and tape remaining time readings will be
incorrect.
● During search, still, or frame-by-frame playback, the picture
will be distorted, and there may be a loss of colour.
● Depending on the type of TV, the top and bottom portions of
superimposed displays may be cut off during NTSC playback.
8 AUTO POWER OFF — 3H / OFF
When this function is set to “3H,” the unit is turned off
automatically if no operation is done within 3 hours. “AUTO
POWER OFF IN 3 MIN” appears on the screen 3 minutes before
the unit is turned off.
XV48EX_EN_01.book Page 54 Saturday, October 9, 2004 10:34 PM