JVC 0905TNH-FN-FN - Manual (Page 20)

20
G
ett
ing
S
tarted
EN
Manual Tuning
Manually tune each channel.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2 Select “Channel” using
[Cursor
U / D], then press [ENTER].
3 Select “Manual Tuning” using
[Cursor
U / D], then press [ENTER].
4
Select “Position” using
[Cursor
U / D], then press [ENTER].
5
Select the position number you wish
to use using [the Number buttons] or
[Cursor
U / D], then press
[RETURN].
You can select position numbers 01 to 99.
6 Select “Channel” using
[Cursor
U / D], then press [ENTER].
7 Press [Cursor U / D] to start
scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4]. Or press [4] and then “– – 4”
appears and wait for 2 seconds.)
• If this is the channel you want, press [RETURN].
This unit can receive the Hyper and Oscar
frequency bands.
• If “Skip” is set to “ON,” select “Skip” using
[Cursor U / D], then press [ENTER]. Select
“OFF” using [Cursor U / D], then press
[RETURN].
• If you want to decode scrambled signals, select
“Decoder” using [Cursor U / D], then press
[ENTER]. Select “ON” using [Cursor U / D],
then press [RETURN].
• To store another channel, repeat steps 4 to 7.
8
After completion, press [SET UP] to
exit.
To Select a Channel
Notes on using the Number buttons:
• Enter channel numbers as a two-digit number for
the quickest result. For example, to select channel
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only select
channels 1 to 99.
• You can select the external input mode “AV1,” “AV2”
or “AV3.”
• To select “AV1,” press [0], [0], [1].
• To select “AV2,” press [0], [0], [2].
• To select “AV3,” press [0], [0], [3].
To Skip a Preset Channel
You can set the unit to skip channels you can no
longer receive or seldom watch when you access
channels using [PR +/-].
1 Follow steps 1 to 3 in “Manual
Tuning.”
2
Select “Position” using
[Cursor
U / D], then press [ENTER].
3 Select the position number you wish
to skip using [the Number buttons]
or [Cursor
U / D], then press
[RETURN].
4 Select “Skip” using [Cursor U / D],
then press [ENTER].
5
Select “ON” using [Cursor U / D],
then press [RETURN].
• To skip another channel, repeat steps 2 to 5.
6
Press [SET UP] to exit.
Channel Plan
Ch. Indication TV Channel
02 - 12 E2 - E12
13 - 20 A - H (only ITALY)
21 - 69 E21 - E69
74 - 78 X, Y, Z, Z+1, Z+2
80 - 99, 100 S1 - S20, GAP
121 - 141 S21 - S41
Channel 12
Decoder OFF
Skip ON
Position P01
Manual Tuning VCR DVD
E9770ED_EN.book Page 20 Wednesday, August 3, 2005 6:35 PM