JVC DR-MV5BEK - Manual (Page 29)

Masterpage:Right0
EN
29
Filename [MV5SEK_08Basic TimerDub.fm]
Page 29Wednesday, 31 August 2005 19:58
TIMER RECORDING
You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
With the VIDEO Plus+ system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognise.
You can use the remote control to enter the PlusCode number.
NOTES:
● There may be cases that the VIDEO Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with the VIDEO Plus+ Timer Programming function, the beginning of
the second one may be left off the recording.
● S
HOW V IEW Timer Programming is not possible on the discs used
exclusively for On-Disc Timer Programming.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
● To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to “Satellite Receiver Users (DVD
Deck Only)” above.
1
Press DVD or VHS to select the deck on which you want to
perform timer programming.
2
For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3
Press VIDEO Plus+ to access the VIDEO Plus+ screen.
4
Press the number buttons to
enter the PlusCode number of a
programme you wish to record,
then press ENTER.
● If you have made a mistake, press
CANCEL and input the correct
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR (8).
● If the number you entered is
invalid, “PLUSCODE NO. ERROR CONFIRM PLUSCODE NO.
THEN RETRY” appears on the TV screen. Input a valid PlusCode
number.
● If “GUIDE PROGRAMME IS NOT SET” appears on the TV screen,
set Guide Program numbers manually. (
੬ pg. 83)
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel some
of the reserved programmes. (
੬ pg. 34)
5
The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press RETURN.
6
Press w e to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” ( ੬ pg. 30, “Weekly/Daily Recording”)
● “VPS/PDC” ( ੬ pg. 30, “PDC Recording”)
● “REC MODE” ( ੬ pg. 27, 28, “Recording Mode”)
● “NAME” ( ੬ pg. 67, “Modify Title Name”) (DVD deck only)
7
Press ENTER to access the Programme Confirmation screen.
8
Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 35.
9
Press TIMER # to engage the unit’s timer mode. The DVD timer
indicator lights up on the unit and the unit is automatically turned
off.
● To disengage the timer mode, press TIMER # again.
VIDEO Plus+ Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VIDEO Plus+ programme screen in step 5.
When this happens, set the correct Guide Program number for that
station. (
੬ pg. 83, “VIDEO Plus+ System Setup”)
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using the VIDEO Plus+
system:
A Perform “VIDEO Plus+ Timer Programming”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Leave the satellite receiver’s power on.
ENTER
CLEAR ( )
DVD
0 – 9
VHS
CANCEL
VIDEO Plus + TIMER
RETURN
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “VIDEO Plus+ System Setup” (
੬ pg. 83) and
set the Guide Program number correctly.
1 2 3
4 5 6
7 8 9
0
SP
1 2 3 4
VIDEO Plus+ PRGM
DATE START STOP TV PROG
DAILY/WEEKLY VPS/PDC
ON
NAME
ENTER PLUSCODE NO. WITH [0-9] KEYS
THEN PRESS [ENTER] OK
REC MODE
PLUSCODE NO.
MV5SEK_00.book Page 29 Wednesday, August 31, 2005 7:58 PM