JVC DLA-M2000LU - Manual (Page 23)

No.51781
1-23
DLA-M2000LU DLA-M2000LE
36
Basic Operations
■ Remote control unit
FREEZE message
FREEZE inhibit message
DIGITAL ZOOM inhibit message
Displaying a Still Picture (FREEZE)
While projecting an image, a still picture is obtained at any
time by using the FREEZE button on the remote control.
When you press the FREEZE button:
“FREEZE” appears on the screen for a few seconds and
then the still picture is shown on the screen. Refer to the
FREEZE message shown on the left of this page.
* To forcibly clear “FREEZE”, press the ESCAPE button.
When you press the FREEZE button again.
The original image resumes.
Notes
• During freezing, the picture sent from the signal source is lost.
• If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”,
“KEYSTONE”) are pressed while displaying a still picture,
“FREEZE” is displayed on the screen.
• This function will not work with some signal sources
(UXGA, etc). In this case, the FREEZE inhibit message
appears for a few seconds, as shown on the left. To forcibly
clear this message, press the ESCAPE button.
Zooming a Part of the Image (DIGITAL
ZOOM +/–)
A part of the image being projected can be digitally magnified up
to four times. When the DIGITAL ZOOM + or – button is
pressed, “Digital zoom” appears on the screen together with the
level bar and magnifying power (
Ч 1.0, Ч 1.2, Ч 1.4, Ч 1.6, Ч 2.0,
Ч 2.5, Ч 3.2, Ч 4.0). When “15 sec.” is displayed in the menu,
“Digital zoom” will appear in approximately 15 seconds.
• To zoom up or zoom down, press the DIGITAL ZOOM + or
– button on the remote control.
Moving the zoomed image:
While “Digital zoom” appears on the screen, you can move
the zoomed image with the cursor (
5 / ∞ / 2 / 3 )/ENTER button
on the remote control.
5 : Upper part of the image will be
displayed.
∞ : Lower part of the image will be
displayed.
2 : Left side part of the image will
be displayed.
3 : Right side part of the image
will be displayed.
Notes
• This function will not work with some signal sources
(UXGA, etc). In this case, the DIGITAL ZOOM inhibit
message appears for a few seconds, as shown on the left. To
forcibly clear this message, press the ESCAPE button.
• The quality of the zoomed image reduces in comparison
with the original one.
• To return to the original size ( × 1.0) and original position,
press the PRESET button while “Digital zoom” is displayed
on the screen.
U T
D W FOCUS –
+ ZOOM SHIFT
VOLUME –
+ QUICK ALIGN. SHUTER –
+
EN T E R
HIDE OPERATE
PRESET
ESCAPE
DIGITAL ZOOM KEYSTONE
PC +
–
VIC SELECT
MENU
FREEZE
VIDEO
RM-M2000 REMOTE CONTROL UNIT
FREEZE
button
PRESET
button
ESCAPE
button
DIGITAL ZOOM
+/-button
Cursor
(
5 / ∞ / 2 / 3)/
ENTER button
FREEZE
FREEZE
D.ZOOM
FREEZE Remote control unit
Digital zoom 1.2
DIGITAL ZOOM
+
–
Remote control unit
EN
TE
R
37
ENGLISH
DEUTSH
FRAN
Ç
AIS
ITALIANO
ESPA
Ñ
OL
Menu Operations
You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the
following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there
are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed,
the projector enters one of these modes by judging the input signal being received.
■ Menu Transition Diagram in No signal Menu Mode
This is displayed if there is no signal from the selected input terminal.
■ Quick Reference Guide for No signal Menu Mode
Main Menu in No signal Menu Mode
Options
Right Left rev.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.: OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:] Selectable sleep times. If no-signal condition continues for the period of selected time (Unit:
Minutes), the projector enters the stand-by mode. 15 / 30 / 60 / OFF*
PC2 (BNC): RGB* or YP B P R . Set to RGB when a computer device with analog RGB, V, H/Cs signals is
connected to the PC2 terminals. Set to YP B P R when a device with component signals (Y, B-Y, R-Y)
or DTV-format signals (Y, P B , P R ) are connected to the PC2 terminals.
Language Language for on-screen display.
Japanese / English* / German / Spanish / Italian / French
Information
Input: Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, or PC2)
Switcher: Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to indicate
that it is not being used.)
Lamp time: Accumulated used hours of the light-source lamp.
RGB YP B P R
Menu
Options
Language
Information
English
Deutsch
Español
Italiano
Français
Menu
Options
Language
Information
Input
Switcher
Lamp time
PC1
CH.0
123 h
Language
Options
Right Left rev.
Top Bottom inv.
RS-232C [bps]
Sleep time [min]
PC2 (BNC)
OFF
OFF
9600
ON
ON
19200
15 30 60 OFF
English
Deutsch
Español
Italiano
Français
Menu
Options
Language
Information
Right Left rev.
Top Bottom inv.
RS-232C
Sleep time
PC2 (BNC)
Main menu in No signal Menu Mode Submenus in No signal Menu Mode
Press 5/∞ to select an item.
Press 5/∞ to select an item.
Press 2/3 to set the value.
Press 5/∞ to select an item.
3 or ENTER
ESCAPE
3 or
ENTER
ESCAPE
∞ 5
∞ 5 ∞
5