JVC CA-MXJ787V - Manual (Page 16)

11
English
Program Play Random Play
Continuous Play
3
Press one of the disc number buttons
(CD 1, CD 2, and CD 3) r, 1 to
select the disc number you want to
play.
CD 1
CD 2
CD 3
Track number
PROGRAM
2 3 1
Program step number Disc number
4
Select a track from the CD selected in the above
step.
On the unit: On the unit:
Press 4 ; or ¢ ; to select the track number, then press
SET k.
On the remote control: On the remote control:
Press the number buttons &.
• For how to use the number buttons,
see “To go to another track directly
using the number buttons” described
to the left.
PRESET
SET
SEA CONTROL
To locate a particular point in a track
During play, press and hold 1 x or ¡ x.
• 1: Fast reverses the disc.
• ¡: Fast forwards the disc.
When using the remote control, press and hold
1 / 4 0 or ¢ / ¡ (.
To go to another track
Press 4 ; or ¢ ; repeatedly before or during
playback.
•
4: Goes back to the beginning of the current
or previous tracks.
• ¢: Skips to the beginning of the next or
succeeding tracks.
When using the remote control, press 1 / 4 0
or ¢ / ¡ ( during or before playing.
If you press and hold 4 4 4 4 4 / ¢ ¢ ¢ ¢ ¢
; (or 1 1 1 1 1 /
4 4 4 4 4 0 0 0 0 0 or ¢ ¢ ¢ ¢ ¢ / ¡ ¡ ¡ ¡ ¡ ( before playing)
You can change the tracks continuously.
To go to another track directly using the number buttons
Pressing the number button(s) & before or during play allows you
to start playing the track number you want.
Ex.: For track number 5, press 5.
For track number 15, press +10,
then 5.
For track number 20, press +10,
then 10.
For track number 32, press +10,
+10, +10 then 2.
Programming the Playing Order of the Tracks —
Program Play
You can arrange the order in which the tracks play before you start
playing. You can program up to 32 tracks.
• To use Repeat play (see page 12) for Program play, press REPEAT
n after starting Program play.
1
Load discs.
• If the current playing source is not the CD player, press CD
6 y, _, then 7 z, + before going to the next step.
2
Press PROGRAM/RANDOM v button
repeatedly until “PROGRAM”
appears on the display.
TUNING
PRESET
PREV NEXT
PROGRAM
2 3 1
• Each time you press the button, CD play mode changes as
follows:
PROGRAM
2 3 1
13
5
Program other tracks you want.
• To program tracks from the same disc, repeat step 4.
• To program tracks from a different disc, repeat steps 3 and 4.
6
Press CD 6 y, _.
The tracks are played in the order you have programmed.
To stop during play, press 7 z, +.
To exit from Program play mode, press PROGRAM/
RANDOM v repeatedly again before or after play so that the unit
enters another play mode. (The program you have made is stored in
memory until you erase the program.)
• If a program has been stored in memory, the program is called
up.
Continued
PROGRAM
/ RANDOM
CENTER MODE
DELAY TIME
PRO LOGIC 3 STEREO TEST TONE
CENTER
LEVEL
REAR
LEVEL
BALANCE
+
+
–
–
R L
CENTER MODE
DELAY TIME
PRO LOGIC 3 STEREO TEST TONE
CENTER
LEVEL
REAR
LEVEL
BALANCE
+
+
–
–
R L
EN6-17;MX-J777V/PM6 7/8/99, 9:16 AM 11