Sony UP20 - Manual (Page 58)

Mis
c
e
llan
eous
Specifications
58
Specifications
Power requirements
100 to 120 V AC only, 50/60 Hz
(for 100 to 120 V AC users)
220 to 240 V AC only, 50/60 Hz
(for 220 to 240 V AC users)
Power consumption
About 1.8 A max. at 25°C
(for 100 to 120 V AC users)
About 1.0 A max. at 25°C
(for 220 to 240 V AC users)
Operating temperature
5°C to 35°C (41°F to 95°F)
Operating humidity
20% to 80% (no condensation allowed)
Storage and transport temperature
–20°C to 60°C (–4°F to 140°F)
Storage and transport humidity
20% to 90% (no condensation allowed)
Dimensions About 212 Ч 125 Ч 395 mm (w/h/d)
(8 3/8 Ч 5 Ч 15 5/8 inches)
Mass About 6.5 kg (14 lb 5 oz)
Printing system Dye transfer sublimation printing
Printable pixels When using the UPC-21S and printing
the full-image:
In NTSC mode: 1524 × 976 dots
(when the H WIDTH and V WIDTH
are set to 1016 and 488 on the
WINDOW SETUP menu)
In PAL mode: 1524 × 1176 dots
(when the H WIDTH and V WIDTH
are set to 1016 and 588 on the
WINODW SETUP menu)
When using the UPC-21L and printing
the full-image:
In NTSC mode:2032 × 1452 dots
(when the H WIDTH and V WIDTH
are set to 1016 and 488 on the
WINDOW SETUP menu)
In PAL mode: 2032 × 1458 dots
(when the H WIDTH and V WIDTH
are set to 1016 and 588 on the
WINODW SETUP menu)
Total gradation 256 levels each for yellow, magenta,
and cyan
Printing time When using the UPC-21S:
When PRN SPEED is set to HIGH
on the PRINTER SETUP menu
In NTSC mode: Approximately 16
seconds
In PAL mode: Approximately 17
seconds
When PRN SPEED is set to
NORMAL on the PRINTER
SETUP menu
In NTSC mode: Approximately 24
seconds
In PAL mode: Approximately 27
seconds
When using the UPC-21L:
When PRN SPEED is set to HIGH
on the PRINTER SETUP menu
In NTSC mode: Approximately 25
seconds
In PAL mode: Approximately 25
seconds
When PRN SPEED is set to
NORMAL on the PRINTER
SETUP menu
In NTSC mode: Approximately 40
seconds
In PAL mode: Approximately 40
seconds
TV system Selectable with the NTSC/PAL
selector
In NTSC mode: NTSC/EIA
standards
In PAL mode: PAL B.G.I. standards
Input connectors
RGB SYNC (analog RGB signal)
(only for the UP-21MD):
BNC connector × 4
RGB: 0.7 Vp-p, 75 ohm terminated
SYNC: 0.3 to 4 Vp-p, 75 ohm
terminated, sync negative
SYNC ON G:
Automatic discrimination
S VIDEO (Separate luminance (Y) and
chrominance (C) signals):
4-pin mini-DIN × 1
Y: 1 Vp-p, 75 ohm terminated, sync
negative
C: For NTSC/EIA standards:
0.29 Vp-p color burst, 75 ohm
terminated
For PAL B.G.I. standards:
0.3 Vp-p color burst, 75 ohm
terminated
VIDEO (NTSC composite video signal
for NTSC/EIA standards and PAL
composite video signal for PAL
B.G.I. standards):
BNC connector × 1
1 Vp-p, 75 ohm terminated, sync
negative
AC IN (for power input)
Output connectors
RGB SYNC (analog RGB signal)
(only for the UP-21MD):
BNC connectors × 4
RGB: 0.7 Vp-p, 75 ohm terminated