SoundCraft UREI 1601E User Manual
Page 54
54
Polarity:
Sometimes erroneously referred to as ‘phase’ this is the + / - sense of a balanced signal or
loudspeaker connection. Reversed polarity should be avoided and checked for as it can cause
uncomfortable phasing effects as the listener moves between the speakers. Polarity Reverse is often
used to correct for wrongly wired cables and connectors.
Pre-fade:
The signal is taken from a point in the circuit which is before the fader.
Post-fade:
The signal is taken from a point in the circuit which is after the fader.
RIAA:
Record Industry of America Association, responsible for the long established equalisation standard
that is applied to the signal produced by a turntable cartridge. Due to the physical limitations of vinyl
reproduction the stylus produces a reasonable level high frequency signal but a much less lower level
low frequency. An RIAA pre-amplifier compensates for this by attenuating the high and boosting the
low frequencies.
Reverberation:
The way in which sound reflects and bounces around the room after the source is removed. This
depends on the size and shape of the room as well as the materials such as carpets, curtains and
clothing that absorb certain frequencies.
Reverb Effect:
This is a signal processor that connects to the console to artificially simulate the reverb effect.
Parameters such as decay time, diffusion and amount of reverb can be controlled. Typically selected
sounds are sent to the processor by turning up the channel post-fade aux sends. The processed (wet)
signal is returned to the mix through a channel where it adds to the direct (dry) signal routed from the
channel fader.
RPM:
Revolutions Per Minute. The measurement of turntable speed, 33, 45 and 78 RPM.
Sampler:
Another performance effect popular with DJs. The channel signal is sent to a digital processor that
samples (stores) a short duration of sound. The output is returned through a channel and replayed by
pressing a trigger. Many samplers provide creative effects such as repeat and reverse. The UREI
sampler is BPM activated.
Scratching:
The art of rhythmically rocking a record back and forward on a turntable, to repeat a certain sound, a
vocal or tone, at the same time operating the cross-fader to create a syncopated “wah wah” chirp
added over a bass heavy back beat.
Signal-to-Noise Ratio (SN): This is the difference expressed in dB between the normal 0dB operating level and the residual noise
floor. It represents how far above the equipment hiss level the signal operates. A higher figure is
better.
Slip mat:
A fabric turntable mat positioned under the record so that the DJ can hold it stationary ready to let go
for a fast start at the point cued.
Split Cue:
A facility to listen to the cue signal in one ear while keeping the program in the other. Used for
matching the beat while cueing a new track. Some consoles provide a CUE/MIX fader to preview the
mix before going live. On the UREI 1601 series this is the xf-monitor.
Sub Bass:
A loudspeaker designed to reproduce only very low frequency sound, typically from around 30 to
120Hz. A crossover is used to route only the low frequencies to the sub.
Tempo:
The rhythmic beat of the music, usually referred to in BPM (Beats Per Minute).
Turntable:
Otherwise known as a ‘record deck’ this plays vinyl discs, still the most popular source for DJ mixing.
It is common for the output of the cartridge to plug directly into the mixing console ‘phono’ input which
provides the RIAA equalisation required. The turntable usually has variable speed control so that the
DJ can synchronise the beat between tracks.
VCA
Voltage Controlled Amplifier: An audio gain element whose level is controlled by a remote DC voltage
rather than through a fader or rotary control. VCA Cross fader functions as an audio cross fader but
with the audio level controlled by a DC voltage produced by the fader. This voltage can be
electronically filtered and is therefore able to remove the clicks, scratches and dropouts associated
with worn audio faders.
XLR:
The professional standard 3 pin round connector used for microphone and other balanced
connections. Equipment female sockets are for inputs, male for outputs.