Sharp DT-300 - Manual (Page 67)

-66
This unit has some inactive pixels within acceptable
tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life
expectancy of the unit. If you have any questions about this
matter, please call toll free 1-800-BE-SHARP (1-800-237-
4277).
U.S.A. ONLY
Specifications
Product type
Model
Video system
Display method
DLP panel
Lens
Projection lamp
Video input signal
S-video input signal
Component input signal
(INPUT 1)
Component input signal
(INPUT 2)
Horizontal resolution
RGB input signal
Pixel clock
Vertical frequency
Horizontal frequency
Rated voltage
Input current
Rated frequency
Power consumption
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector
DT-300
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
DLP chip, RGB optical shutter method
Panel size: 0.6
Љ
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 589,824 dots (1,024 [H]
ן 576 [V])
1–1.2 ן zoom lens, F2.0–2.4, f=16.9–20.2 mm
210 W/168 W SHP lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75
Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75
Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75
Ω terminated
P B : 0.7 Vp-p, 75 Ω terminated
P R : 0.7 Vp-p, 75 Ω terminated
29-pin connector
DVI input signal: Digital 250–1,000 mV 50
Ω
Analog 0.7 Vp-p 75 Ω
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P B : 0.7 Vp-p, 75 Ω terminated
P R : 0.7 Vp-p, 75 Ω terminated
520 TV lines (NTSC 3.58 input)
DVI-I terminal
<Digital>
Input impedance
50 Ω
Input level 250-1000 mV
<Analog>
Input impedance
75 Ω
Input level 0.7 Vp-p
<Synchronization signal>
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 K Ω
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
12–80 MHz
43–75 Hz
15–70 kHz
AC 100–240 V
3.2 A
50/60 Hz
285 W
1,070 BTU/hour
41°F to 95°F (
ם5°C to ם35°C)
מ4°F to 140°F (מ20°C to ם60°C)
Plastic
38 kHz
14
1 ⁄
2
Љ (W) ן 6 9 ⁄
16
Љ (H) ן 12 7 ⁄
8
Љ (D) (368 ן 153.8 ן 327 mm) (including swivel stand)
14 1 ⁄
2
Љ (W) ן 4 5 ⁄
8
Љ (H) ן 12 7 ⁄
8
Љ (D) (368 ן 118 ן 327 mm) (main body only)
10.1 lbs. (4.6 kg) (including swivel stand)
9.0 lbs. (4.1 kg) (main body only)
Remote control, Two AA size batteries, Power cord, Video cable, Lens cap (attached on
the body), Operation manual
Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord (QACCDA007WJPZ), Video cable
(QCNWGA001WJZZ), Lens cap (CCAPHA004WJ01), Operation manual (TINS-
B006WJZZ)
This SHARP projector uses a DMD chip. This very
sophisticated chip contains 589,824 pixels. As with any high
technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
03.10.29, 2:48 PM Page 66