Shelby CS-500S - Manual (Page 14)

. .
. .
15 14
ACTIVE ANTI CAR-JACKING:
1. Press and hold the transmitters and buttons at the same
time for 2 seconds while the vehicle’s ignition is “ON”. The
parking lights will turn “ON” for 1.5 seconds to indicate the
system is in the “Car-jacking Mode”.
2. Once the system is in “Car-jacking Mode” and you are forced
from the vehicle, the system will trigger when the door is opened
and closed while the ignition is in the “ON” position.
PASSIVE ANTI CAR- JACKING:
1. Turn the ignition switch to the “ON” position for entering the “Car-
jacking Mode”.
2. Once the system is in “Car-jacking Mode” and you are forced from
the vehicle, the system will trigger when the door is opened and closed
while the ignition is in the “ON” position.
TRIGGER THE ANTI CAR -JACKING MODE:
a).50 seconds after the system has been triggered. The siren will start
chirping for 15 seconds.
b). During the 15 second period of chirping, you must push the valet
switch once to turn off the car-jacking feature. If not, it will enter the
second timer Anti “Car-jacking Mode”.
c). 65 seconds after the system has been triggered, the siren will start
alarming and the parking lights will continue flashing
d). 90 seconds after the system has been triggered
1. The siren will continue alarming and the parking lights flashing.
2. The starter disable will activate to prevent the vehicle from starting.
3. This will remain active until the vehicle's battery power is diminished.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from the “OFF” to “ON” position, and within 10
seconds push and release the valet/program switch, the siren will stop
and the system is disarmed.
Note: If you use password pin code to double protect the vehicle
security, you will need to use it to completely disarm the system.
OPERATION
P. SYSTEM’S TRIGGER CHECK
(For two-way transceiver operation only)
Press the transceiver F button first, within 3 seconds press
the (C) button. It will respond with one melody sound and
all trigger’s records will immediately be displayed on the LCD
screen.
Note: If there is no response you are out of range.
Q. SYSTEM’S STATUS CHECK
(For two-way transceiver operation only)
When you want to check the system’s present status through
the LCD screen, press the transceiver F button twice, within
3 seconds press the (C)button. It will respond with one
melody sound, the LCD screen should be illuminated.
Note: If there is no response you are out of range.
OPERATION
R. DRIVER PAGING (For two-way transceiver operation only)
It is useful in the event that someone wants to page the driver of the parked
vehicle.
Indoor Driving Paging
Under the ignition switch “off” condition, press and hold the valet switch
for 2 seconds to page the driver, one chirp sound shall be emitted from the
vehicle and the paging melody sound continues on your Remote LCD
transceiver and “ ” indication flashes on the LCD screen.
Outdoor Driving Paging
If someone tries to page you by tapping the paging (knock) sensor (optional)
which is usually mounted on the bottom part of front window, the paging
melody sound continues sounding on your Remote LCD transceiver and “ ”
indication flashes on the LCD screen.
1. Press the transmitter F button first, within 3 seconds press ( ) button
to activate outdoor driver paging function, It responds with chirps of the
vehicle, a melody sound and " " indication flashes on the LCD screen
to confirm the function is on.
2. When tapping the paging (knock) sensor, one chirp sound shall be emitted
from the vehicle and the paging melody sound continues sounding on
your Remote LCD transceiver and “ ” indication flashes on the LCD
screen.
3. Turn on the ignition switch; OR press the button to arm the system;
OR press the button to disarm the system, this outdoor driver paging
function will exit.