Samsung SP-H700 - Manual (Page 3)

User Instructions
The Federal Communications Commission
Radio Frequency Interference Statement includes
the following warning:
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television receptions,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the
equipment and receiver.
● Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
User Information
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment. If necessary, consult your
dealer or an experienced radio/television
technician for additional suggestions. You may
find the booklet called how to Identify and
Resolve Radio/TV Interference Problems helpful.
This booklet was prepared by the Federal
Communications Commission. It is available
from the U.S. Government Printing Office,
Washington, DC 20402, Stock Number 004-
000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Warning
User must use shielded signal interface cables to
maintain FCC compliance for the product.
Provided with this monitor is a detachable power
supply cord with IEC320 style terminations. It
may be suitable for connection to any UL Listed
personal computer with similar configuration.
Before making the connection, make sure the
voltage rating of the computer convenience
outlet is the same as the monitor and that the
ampere rating of the computer convenience
outlet is equal to or exceeds the monitor voltage
rating.
For 120 Volt applications, use only UL Listed
detachable power cord with NEMA
configuration 5-15P type (parallel blades) plug
cap. For 240 Volt applications use only UL
Listed Detachable power supply cord with
NEMA configuration 6-15P type (tandem blades)
plug cap.
------------------------------------------------------------
IC Compliance Notice
This Class B digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations of ICES-003.
Cet appareil Numérique de classe B respecte
toutes les exigences du Règlemo équipements
produisant des interférences au Canada.
------------------------------------------------------------
PCT Notice
------------------------------------------------------------
VCCI
This is a Class B product based on the standard
of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI).
If this is used near a radio or television receiver
in a domestic environment, it may cause radio
interference. Install and use the equipment
according to the instruction manual.
Preparation
FCC Information
5
FCC Information
Preparation
Important Safety Information
4
Important Safety Information
(continued)
● Use only a grounded or polarized outlet. For your safety, this set is equipped with a
polarized alternating current line plug having one blade wider than the other. This
plug will fit into the power outlet only one way. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug still does not fit, contact your
electrician to replace your outlet.
● Protect the power cord. Power supply cords should be routed so that they won’t be
walked on or pinched by objects placed on or against them. Pay particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the unit.
● Unplug the set from the wall outlet and disconnect the antenna or cable system during
a lightning storm or when left unattended and unused for long periods of time. This
will prevent damage to the unit due to lightning and power-line surges.
● Do not overload the wall outlet or extension cords. Overloading can result in fire or
electric shock.
● Do not insert anything through the openings in the unit, where they can touch
dangerous voltage points or damage parts. Never spill liquid of any kind on the set.
● Do not attempt to service the set yourself. Refer all servicing to qualified service
personnel. Unplug the set from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
- when the power-supply cord or plug is damaged
- if liquid has been spilled on the unit or if objects have fallen into the set
- if the set has been exposed to rain or water
- if the set does not operate normally by following the operating instructions
- if the set has been dropped or the cabinet has been damaged
- when the set exhibits a distinct change in performance
● If you make adjustments yourself, adjust only those controls that are covered by the
operating instructions. Adjusting other controls may result in damage and will often
require extensive work by a qualified technician to restore the set to normal.
● When replacement parts are required, be sure the service technician uses replacement
parts specified by the manufacturer or those that have the same characteristics as the
original part. Unauthorized substitutions may result in additional damage to the set.
● Upon completion of any service or repairs to this set, ask the service technician to
perform safety checks to determine that the set is in a safe operating condition.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.