Sony AEP MODEL CPD-E200E - Manual (Page 23)

5-5 5-6
5-2. CIRCUIT BOARDS LOCATION
D
A
H
5-3. SCHEMATIC DIAGRAMS AND PRINTED
WIRING BOARDS
G
D
S
2
3
4
5
6
7
8
9
0
!¡
!™
!¢
!§
–
1
G
D
S
G
S S
D
G
D
Ver.1.6
Transistor
(FET)
Transistor
Transistor
Discrete semiconductot
(Chip semiconductors that are not actually used are included.)
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Source
Source
Anode Anode
(NC)
(NC)
Cathode
Anode
Cathode
Common
Cathode Cathode
Common
Cathode Cathode
Common
Common
Common
Common
Cathode
Anode
Base Emitter
Collector
Base Emitter
Collector
Drain
Gate
Gate
Drain
Device Printed symbol Terminal name Circuit
Terminal name of semiconductors in silk screen
printed circuit ( )
Anode
Anode
Anode Cathode
Anode Anode
Cathode
!£
Transistor
(FET)
Transistor
(FET) !∞
Emitter
Collector
Base
Transistor
Source
Gate
Drain
Cathode
Anode
Anode
Cathode
Anode
Anode
*
Note:
• All capacitors are in µ F unless otherwise noted. (pF: µµ F)
Capacitors without voltage indication are all 50 V.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
• All resistors are in ohms.
•
f
: nonflammable resistor.
•
F
: fusible resistor.
• ¢ : internal component.
•
p
: panel designation, and adjustment for repair.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
•
e
: earth-ground.
•
E
: earth-chassis.
• All voltages are in V.
• Readings are taken with a 10 M Ω digital multimeter.
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal production
tolerances.
• * : Can not be measured.
• Circled numbers are waveform references.
•
s
: B + bus.
•
S
: B – bus.
• The components identified by [ in this basic schematic diagram
have been carefully factory-selected for each set in order to
satisfy regulations regarding X-ray radiation.
Should replacement be required, replace only with the value
originally used.
• When replacing components identified by ] , make the
necessary adjustments indicated. (See page 3-1)
• When replacing the part in below table, be sure to perform the
related adjustment.
Note: The components identified by shading and mark
! are critical for safety. Replace only with part
number specified.
Part Replaced ( [ )
RV501 HV ADJ
HV Regulator
Circuit Check
HV Protector
Circuit Check
Beam Current
Protector Circuit
Check
Part Replaced ( ] )
D board IC501, C532, C534,
C539, C553, C554,
C555, C556, C558,
C561, R541, R542,
R544, R564, R567,
R568, RV501,
T501 (FBT)
D board IC607, IC901, D515,
D517, C540, C542,
C544, R510, R543
R547, R549, R552,
R595,
T501 (FBT)
D board IC605, IC607, IC901,
C535, C541, R545,
R546, R548, R550,
R596, R934,
T501 (FBT)
• Divided circuit diagram
One sheet of D board circuit diagram is divided into four
sheets, each having the code D- a to D- d . For example, the
destination ab1 on the D- a sheet is connected to ab1 on the
D- b sheet.
b 1 a
Ref. No.
Circuit diagram division code