Sony HDW-2000 - Manual (Page 31)

1-25
HDW-2000/M2000/M2000P/S2000/S2000P/M2100/M2100P, DVW-2000/2000P/M2000/M2000P
MSW-2000/A2000/A2000P/M2000/M2000P/M2000E/M2000EP/M2100/M2100P/M2100E/M2100EP
1-14. Reference System
1-14-1. Recorder
For each reference signal of the recorder, either of an
external reference video signal (*3) or input video signal
(*4) is automatically selected according to the setting of
function menu item OUT REF, the setting of setup menu
ITEM-309, and the operation mode (PB/EDIT/REC) of
this unit. (Refer to the table 1-14-1 below.)
In case of DVW series and MSW series, the reference
signal (clock) of an analog video signal in an A/D convert-
er regards the analog video signal itself as a reference
signal under any setting.
m
. To select the video input, open the HOME page on the
function screen and use the F1 button (VID. IN).
. To set the OUT REF, open the P4 page (MISCELLA-
NEOUS) on the function screen and use the F2 button
(OUTREF).
Audio Signal Independent Recording
Even if an input video signal is selected as the reference
signal, the reference signal is automatically selected to an
external reference video signal for the period in which the
no input video signal is input. When no external reference
video signal is input, the internal-generated reference
signal is automatically selected for the period.
An audio signal can be independently recorded by this
system even if no reference video signal is input from the
outside.
n
In the case of DVW series and MSW series, when the
setup menu ITEM-185 (AUDIO SAMPLING RATE
CONVERTER) set to “44 kHz” or “32 kHz”, an audio
signal can be independently recorded.
1-14. Reference System
Alarm Display for Video Input Signal and
Reference Signal
1. Blink of the selected input video indication
area of the video input selection
This area at the HOME page on the function screen blinks
when signal is not input to the connector selected by the
video input selection.
2. Blink of the STOP button
The button blinks when the reference signal is not locked
to an input video signal.
(This function can be canceled in the setup menu ITEM-105.)
. When the OUT REF is set to “INPUT”:
The STOP button blinks when the signal is not input to
the connector selected by the video input selection.
. When the OUT REF is set to “REF”:
The STOP button blinks in the following either cases.
When no reference signal is input to REF. VIDEO connector.
When the reference video signal (REF.VIDEO input) is
not synchronized with an input video signal selected by
the video input selection.
1-14-2. Player
The player regards the external reference video signal as a
reference signal. However, when no external reference
video signal (REF./REF. VIDEO INPUT) is input, the
player automatically switches to the reference signal
generated inside the unit.
Alarm Display for Reference Signal
Blink of the STOP button
The STOP button blinks when the signal is not input to the
REF./REF. VIDEO INPUT connector.
(This function can be canceled in the setup menu ITEM-105.)
Table 1-14-1. Reference System for Recorder
Menu ITEM-309 EXT AUTO
OUT REF ————— REF INPUT
Operation mode ————— PB EDIT (*1) EDIT (*2) REC —————
Video input A/D
(DVW/MSW series only)
Video output process
Digital audio External Reference Video (*3) Input Video (*4)
Servo system
*1: When the setup menu ITEM-309 is set to “AUTO1”.
*2: When the setup menu ITEM-309 is set to “AUTO2”.
*3: REF. VIDEO input
*4: The input video signal is selected by the video input selection.