KORG TONEWORKS AX10G - Manual (Page 12)

12
AMBIENCE
Use the AMBIENCE selector to choose an ambience effect, and use the DEPTH buttons to adjust the DEPTH parameter. To
adjust the delay time or reverb time, press the TAP button twice at the desired interval. If AMB is selected as the PEDAL FX,
you can use the expression pedal to control the effect.
TYPE Explanation TAP Normal PEDAL FX: AMBIENCE
DEPTH PEDAL DEPTH
SLAP Slap-type delay whose delay time is a 1/4
of the interval at which you press TAP
ECHO1 Tape echo simulation with a warm tone (feedback low)
ECHO2 Tape echo simulation with a warm tone (feedback medium)
ECHO3 Tape echo simulation with a warm tone (feedback high)
PP DLY Ping-pong delay that bounces from to left to right
MULTI Multi-tap delay
AIR Reverb with an airy feel
ROOM Room reverb
HALL Hall reverb (*8)
PLATE Plate reverb (*8)
SPRING Spring reverb (*8)
Delay time: up
to 250 [ms]
Delay time:
up to 1.0 [s]
N/A (*2)
Reverb time:
up to 4.0 [s]
Reverb time:
up to 8.0 [s]
Effect level:
0~30 Controls the
effect depth
Specifies the
effect depth at
maximum
pedal position
(*8) Sets the reverb time to twice the interval at which you press TAP.
Expression pedal
Selecting the effect that will be controlled by the
pedal
Press the PEDAL FX button to select the effect that
will be controlled by the pedal. The LED located at
the left indicates the effect (or volume) that will be
controlled.
ORG:WAH (orange): Pedal wah
RED:MOD (red): The effect selected by MODULATION
GRN:AMB (green): The effect selected by AMBIENCE
OFF:VOLUME (unlit): Volume pedal
If an effect other than WAH is selected for the pre-
effect, you cannot select WAH from the PEDAL FX
button. If WAH is selected as the pedal effect,
changing the pre-effect to something other than
WAH will switch the pedal effect to VOLUME.
Using the pedal to switch the effect on/off
By advancing the pedal all the way forward you can
switch the selected PEDAL FX effect on/off. When
the effect is on, the LED at the left of the pedal will
light. If VOLUME is selected as the PEDAL FX, the
LED cannot be turned off.
Setting the minimum value of the volume pedal
If PEDAL FX is set to VOLUME, you can hold down
the FUNCTION switch and use the AMBIENCE
DEPTH buttons to specify the minimum volume (VOL
PEDAL MIN) that will be controlled by the pedal.
Saving the sound of a specific pedal position
You cannot save the sound produced by a specific
pedal position. The pedal effect will always modify
the sound according to the actual current position of
the pedal.
NR (Noise Reduction)
You can adjust the amount of noise reduction by
holding down the FUNCTION button and turning the
VOLUME (NR) control knob.
Depending on the connected device, excessively
high NR settings may cause notes to be cut off. If
this happens, lower the level.
Storing a program
When you have created a sound you want to keep,
you can write (store) it into one of the 40 user
programs (0.1~9.4).
If you switch programs or turn off the power before
writing your edited program, the changes you made
will be lost.
The program that had been in the writing destina-
tion will be overwritten.
1. Press the WRITE button. The program number
will blink in the display, and the AX10G will be in
“write-ready” mode.
2. Use the program select switches to select where
you would like to store the program.
You cannot write to a preset program (01~94).
3. Press the WRITE button to write the program into
the selected program number.
If you decide not to write, press either of the
MASTER (CANCEL) buttons to exit write-ready
mode (display blinking). You will return to normal
operation.
2
3
1, 3