KORG TONEWORKS AX10G - Manual (Page 6)

6
Parts and what they do
Front panel
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1 Display
This shows the program number and when you
operate a knob or button, the value of that parameter
will briefly appear in the display.
• This will light when the power is on.
• The dot in the lower right of the display will light
when you edit a parameter value.
• If the AX10G is running on batteries, will blink
when the batteries run low.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2 AMP TYPE selector
This selects one of 11 types of amp models.
3 Control knobs
These knobs adjust the gain, tone, and volume of the
amp models.
You can adjust the depth of the noise reduction (NR)
by holding down the FUNCTION button and turning
the VOLUME/NR knob.
Some settings of these knobs may cause distortion
in your sound. If this occurs, lower the VOLUME
control knob (or MASTER buttons).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
4 PRE FX (TUNER) LED
These indicate the selected pre-effect.
The LEDs will not light if the pre-effect is off.
When the tuner is operating, these LEDs indicate the
difference from the correct pitch. (p.9)
5 PRE FX button
Each time you press this button, the pre-effect type
will change in the order of COMP
→
WAH
→
ACOUSTIC
→
COMP.
6 VALUE (CALIB) buttons –ON/OFF–
These buttons adjust the value of the pre-effect.
You can switch PRE FX on/off by pressing the
VALUE
▲
and
▼
buttons simultaneously.
When the tuner is operating, you can use these
buttons to adjust the calibration (CALIB).
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
7 MODULATION selector
This selects one of 11 types of modulation effect.
8 DEPTH/SPEED buttons –ON/OFF–
These buttons adjust the depth etc. of the modulation
effect (DEPTH).
You can adjust the modulation speed etc. by holding
down the FUNCTION button and pressing these
buttons (SPEED).
You can switch the MODULATION effect on/off by
pressing the DEPTH
▲
and
▼
buttons simulta-
neously (ON/OFF). When off, the MODULATION
selector LED will not be lit.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
9 AMBIENCE selector
This selects one of 11 ambience effects.
10 DEPTH buttons –ON/OFF–
These buttons adjust the depth etc. of the selected
ambience effect.
You can switch AMBIENCE on/off by pressing the
DEPTH
▲
and
▼
buttons simultaneously (ON/OFF).
When off, the AMBIENCE selector LED will not be lit.
If the expression pedal is controlling volume, you can
set the minimum volume (i.e., when the pedal is fully
returned) by holding down the FUNCTION button
and pressing
▲ or ▼ .
11 TAP button
You can set the delay or reverb time of the ambience
effect by tapping this button at the desired interval.
The LED located at the left will blink to indicate the
tempo.
1 3
4
5
6
2
7
8
9
10
12
13
14
15
11
16
17
18
19