Lynx EPM-4 - Manual (Page 17)

CMOS Setup / Boot Procedure
EPM-4 Reference Manual Configuration / Operation – 9
CMOS Setup / Boot Procedure
• Turn power on.
• Press the DEL key the instant that video is displayed (during the memory test).
• Verify default CMOS Setup information as shown below.
• Insert bootable floppy disk into floppy drive.
• Reset computer using push button reset.
• See VersaLogic KnowledgeBase article
VT1476 – EPM-4 CMOS Setup Reference for
more information about these parameters.
Basic CMOS Configuration
+------------------------------------------------------------------------------+
| System Bios Setup - Basic CMOS Configuration |
| (C) 2002 General Software, Inc. All rights reserved |
+---------------------------+--------------------+-----------------------------+
| DRIVE ASSIGNMENT ORDER: | Date:>JAN 1, 1980 | Typematic Delay : 250 ms |
| Drive A: Floppy 0 | Time: 00 : 00 : 00 | Typematic Rate : 30 cps |
| Drive B: (None) | NumLock: Disabled | Seek at Boot : None |
| Drive C: IDE 0/Pri Master +--------------------+ Show "Hit Del" : Enabled |
| Drive D: (None) | BOOT ORDER: | Config Box : Enabled |
| Drive E: (None) | Boot 1st: Drive A: | F1 Error Wait : Enabled |
| Drive F: (None) | Boot 2nd: Drive C: | Parity Checking : (Unused) |
| Drive G: (None) | Boot 3rd: (None) | Memory Test Tick : Enabled |
| Drive H: (None) | Boot 4th: (None) | Debug Breakpoints: (Unused) |
| Drive I: (None) | Boot 5th: (None) | Debugger Hex Case: Upper |
| Drive J: (None) | Boot 6th: (None) | Memory Test : StdLo FastHi |
| Drive K: (None) +--------------------+-----------------+-----------+
| (Loader): (Unused) | ATA DRV ASSIGNMENT: Sect Hds Cyls | Memory |
+---------------------------+ Ide 0: 3 = AUTOCONFIG, LBA | Base: |
| FLOPPY DRIVE TYPES: | Ide 1: 3 = AUTOCONFIG, LBA | 633KB |
| Floppy 0: 1.44 MB, 3.5" | Ide 2: Not installed | Ext: |
| Floppy 1: Not installed | Ide 3: Not installed | 63MB |
+---------------------------+--------------------------------------+----------- +
Custom Configuration
+------------------------------------------------------------------------------+
| System BIOS Setup - Custom Configuration |
| (C) 2002 General Software, Inc. All rights reserved |
+---------------------------------------+--------------------------------------+
| D0000h 64k page function : ISA bus | COM1 (3F8h) RS-232 : IRQ4 |
| PLD register base I/O : 0E0h | COM2 (2F8h) RS-232 : IRQ3 |
| Force Ethernet 10-BaseT : Disabled | COM3 (3E8h) RS-422/485 : Disabled |
| PS/2 Mouse (IRQ12) : Enabled | COM4 (2E8h) RS-422/485 : Disabled |
| LPT1 (378h) : Disabled | GP Timer 0 : Disabled |
| Parallel Port Mode : FDD | GP Timer 1 : Disabled |
| CPU Speed : 133 MHz | Watchdog Timer : Disabled |
| Cache Mode : Wr-back | PCI Int A : IRQ11 |
| Write Buffer : Enabled | PCI Int B : IRQ11 |
| GP Bus Timings : Normal | PCI Int C (Ethernet) : IRQ11 |
| Console Redirection : Auto | PCI Int D : IRQ11 |
+---------------------------------------+--------------------------------------+
Note: Due to changes and improvements in the system BIOS, the information on your
monitor may differ from that shown above.