Operation, B-2 setting the dip switches, Wire drive head selection – Lincoln Electric LN-10 HEADS & CONTROLS IM587-B User Manual
Page 19: Welding power source selection
B-2
OPERATION
B-2
Setting the DIP Switches
The DIP switches are each labeled with an “ON”
arrow showing the on direction for each of the 8 indi-
vidual switches in each DIP switch (S1 and S2). The
functions of these switches are also labeled and set
as described below:
Wire Drive Head Selection
The LN-10 control is set up for proper presettable wire
feed speed by setting S1 DIP switches (5 to 8) as
appropriate per the following examples for the head
specification and 10 Series wire drive external gear
selection being used:
For K1563-1,-3 or K1564-Series (LN-10 Boom) or
K1559-1 (LN-10 Bench) with 35-500 IPM (0.89-12.7
m/m) Low Speed Ratio set S1 DIP Switch as follows:
For K1563-1,-3 or K1564-Series (LN-10 Boom) or
K1559-1 (LN-10 Bench) with 50-750 IPM (1.25-19.0
m/m) High Speed Ratio set S1 DIP Switch as fol-
lows: (initial factory setting)
LN-10
For K679-1 (Single Head Boom) with 50-770 IPM
(1.27-19.5 m/m) Low Speed Ratio set S1 DIP Switch
as follows:
For K679-2 (Single Head Boom) with 80-1200 IPM
(2.00-30.5 m/m) High Speed Ratio set S1 DIP Switch
as follows:
Note: The K679-1 and -2 require the K1562-1 control box.
Welding Power Source Selection
The LN-10 Control is set up for proper presettable
weld voltage control by setting S1 DIP switches (1 to
4) as appropriate per the following information for the
welding power source being used:
CV-250/CV 300-I:
CV-300/CV 400-I:
CV-400/CV 500-I:
CV-655: (initial factory setting)
V350-PRO And V450-PRO:
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head
For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10
Bench) with 55-825 IPM (1.40-21.0 m/m) Low
Speed Ratio set S1 DIP Switch as follows:
For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10
Bench) with 80-1250 IPM (2.00-31.8 m/m) High
Speed Ratio set S1 DIP Switch as follows:
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
M 4 S R + -
S2
ON
S2
1
2
3
4
5
6
7
8
Head
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head
Pwr Sources
S1
ON
S1
1
2
3
4
5
6
7
8
Head