Lincoln Electric LN-10 HEADS & CONTROLS IM587-B - Manual (Page 9)

WIRE DRIVE OR WIRE DRIVE SECTION OF FEEDER
SPEC.# TYPE LOW SPEED RATIO HIGH SPEED RATIO
Speed Wire Size Speed Wire Size
Solid Cored Solid Cored
K1563-1,-3 10 Series 35-500 IPM .025 - 3/32 in. .035 - .120 in .50 - 750 IPM .025 - 1/16 in. .035 - 5/64 in.
Std Drive Boom Mount (0.89-12.7 M/M) (0.6 - 2.4 mm) (0.9 - 3.0 mm) (1.25 - 19.0 M/M) (0.6 - 1.6 mm) (0.9 - 2.0 mm)
K1563-2,-4 10 Series 55 - 825 IPM .025 - 1/16 in. .035 - 5/64 in. 80 - 1250 IPM .025 - .045 in. .035 - .045 in.
Hi-Speed Boom Mount (1.40 - 21.0 M/M) (0.6 - 1.6 mm) (0.9 - 2.0 mm) (2.00 - 31.8 M/M) (0.6 - 1.2 mm) (0.9 - 1.2 mm)
K679-1 Synergic 7F* 50 - 770 IPM .025 - 1/16 in. .035 - 5/64 in. --- --- ---
Std Drive Boom Mount (1.27 - 19.5 M/M) (0.6 - 1.6 mm) (0.9 - 2.0 mm)
K679-2 Synergic 7F* --- --- --- 80 - 1200 IPM .025 - .045 in. .035 - .045 in.
Hi-Speed Boom Mount (2.00 - 30.5 M/M) (0.6 - 1.2 mm) (0.9 - 1.2 mm)
K1559-1,-3 LN-10 35-500 IPM .025 - 3/32 in. .035 - .120 in. 50 - 750 IPM .025 - 1/16 in. .035 - 5/64 in.
Std Drive Bench Model (0.89-12.7 M/M) (0.6 - 2.4 mm) (0.9 - 3.0 mm) (1.25 - 19.0 M/M) (0.6 - 1.6 mm) (0.9 - 2.0 mm)
K1559-2,-4 LN-10 55 - 825 IPM .025 - 1/16 in. .035 - 5/64 in. 80 - 1250 IPM .025 - .045 in. .035 - .045 in.
Hi-Speed Bench Model (1.40 - 21.0 M/M) (0.6 - 1.6 mm) (0.9 - 2.0 mm) (2.00 - 31.8 M/M) (0.6 - 1.2 mm) (0.9 - 1.2 mm)
CONTROLS, HEADS AND COMPLETE UNITS
SPEC.# TYPE INPUT POWER PHYSICAL SIZE• TEMPERATURE RATING
Dimensions
Height Width Depth Weight Operating Storage
K1562-1 Δ ,-2 Δ LN-10 40-42 Vac + 10% 14.80 “ 14.20 “ 4.20 “ 18.0 Lbs
Control Controls 4.0 Amps 50/60 Hz (K1562-1) (375.9 mm) ( 360.7mm) (106.7 mm) (8.2 Kg)
6.0 Amps 50/60 Hz (K1562-2)
K1563-1 Δ ,-3 Δ 10 Series 7.81 “ 14.71 “ 11.00“ 25.0 Lbs
Std Drive Boom Mount (198.4 mm) (373.6 mm) (27.94 mm) (11.3 Kg)
30.0 Lbs
K1563-2,-4 (13.6 Kg)
Hi-Speed +40°C +40°C
to to
K679-1 Synergic 7F* 11.5“ 7.16“ 8.06“ 16.5 Lbs -20°C -40°C
Std Drive Boom Mount ( 285.8mm) (181.9 mm) (204.7mm) (7.5 Kg.)
K679-2 Synergic 7F*
Hi-Speed Boom Mount
K1559-1,-3 LN-10 40-42 Vac + 10% 20.46 “ 14.73 “ 30.35 “ 65.0 Lbs
Std Drive Bench Model 4.0 Amps 50/60 Hz (K1559-1,-2) (519.7 mm) (366.5 mm) (770.9 mm) (29.5 Kg)
6.0 Amps 50/60 Hz (K1559-3,-4) 70.0 Lbs
K1559-2,-4 (31.8 Kg)
Hi-Speed
A-1 INSTALLATION
LN-10
A-1
TECHNICAL SPECIFICATIONS – LN-10 Heads & Controls
• Excluding Wire Reel
Δ Included with K1561-Series, LN-10 Boom Packages
*Synergic 7F wire drives use 4-roll drives with 2 driven rolls(Drive roll kits not common with 10 Series heads)
GENERAL DESCRIPTION
The LN-10 is a modular line of 42VAC input 4-roll wire feed-
ers. A single control with dual procedure presettability of
wire feed speed (in IPM or M/min) and arc voltage is used
with a single DC welding power source.
The LN-10 models have controls providing keypad or
remote selectability of either of two procedures.
The units offer 4 independently selectable gun trigger
modes for each procedure; cold feed, 2 step and 4-step trig-
ger and spot weld mode.
Also, 4 selectable, presettable timers for each procedure;
preflow, postflow, burnback and spot weld time.
Arc starting can be optimized for each procedure with 5
selectable wire feed acceleration rates, and independent
control of slower run-in procedure.
A gas purge key is provided, as well as cold feed forward
and reverse keys with independently adjustable forward
feed speed setting.
K-1563-1,-2
K-1559-1,-2
K-1559-3,-4
K-1563-3,-4