Lucent Technologies MDW 9000/9010 - Manual (Page 3)

ON MSG
RANGE BATT
PSTAT 18
1 8 2 3
7
6 5
4
- Handset Display -
Your MDC 9000 or MDW 9000/9010 Telephone
1 — Line Status Indicators show status of
outside and inside lines. Arrow or rectangle
“points” to the line button it represents and
flashes in different patterns to show activity
on the line (see box below).
2 — P appears when in program mode.
3 — STAT (MDC 9000 only) appears steady-on
when handset is out of range. Remains until
all line status indicators are updated.
MUTE (MDW 9000/9010 only) appears when
the handset microphone is off.
4 — MSG appears when you have received a voice
mail message.
5 — BATT appears when there are only a few
minutes of conversation time left. Handset
gives 2 short beeps. Place handset on the
base to recharge.
6 — RANGE appears (and handset beeps twice)
if Status (off only) or On/Off button is
depressed when handset is out of the base’s
range. To make or receive calls, move
handset closer to base.
7 — ON appears when the handset is turned on
after you pressed On/Off.
8 — 18 (MDW 9010 only) indicates Local Test
Mode; 1 through 10 are used in Wireless
Test Mode.
To Update Display:
Press
Two Loud Beeps means:
Move Closer to Base Unit
Status
ON MSG
RANGE BATT
PSTAT
Status On/Off Hold
2 ABC 3 DEF 1
6
MNO
9 WXYZ
#
5 JKL
8 PQRS
0 Oper
4 GHI
7
*
Conf Trans Feat
TUV
Ext. 1 6
MDC 9000
STAT/RANGE means:
Move Closer to Base Unit
User Instructions
(MDC 9000) A quick reference
to most important cordless
phone features.
Directory Card
(MDC 9000, behind cover)
Antenna
Headset Jack
(MDC 9000) For headset adapter
cord.
Battery Charging
Contacts
Handset batteries charge through
these contacts. Clean periodically
by rubbing them with a soft gum
eraser.
Status
(MDC 9000) Press to turn on the
display when the handset is off,
or to update the display when the
STAT indicator appears.
Volume Control
(MDC 9000) Slide the switch to
adjust the volume of the earpiece to
Normal or High.
(MDW 9000/9010) An 8-interval
pushbutton controls the ringer
volume when the phone is off and
the receiver volume when the
phone is on.
Mute
(MDW 9000/9010) Press to turn
the microphone on/off so that
you can/cannot be heard by the
caller.
Conf (Conference)
Press to add another party to
your call (see p. 7).
Headset Jack
(MDW 9000/9010) For headset
adapter cord.
Feat (Feature)
Press to enter program mode
(see p. 22).
Handset Extension
Label
Write the extension number
on this label using a pencil
or ballpoint pen only.
Trans (Transfer)
Press to transfer a call to
another extension (see p. 7).
Handset Display
Displays status of lines and
range. For details, see figure
opposite.
Outside Line/
Programmable/
Intercom/ Drop
Buttons (6)
See Line Buttons,
p. 3, for line button
assignments.
Hold
Press to put a call on hold
(see p. 7).
On/Off
To turn the handset on, press
once. ON appears in the
display. To turn off, press
again. Turn on to make or an-
swer a call, and turn off to hang
up (see p. 7).
1
Flash Long on, long off indicates a ringing call.
Wink Long on, short off indicates a call on hold.
indicates the line you’re using.
- Line Status Indicators -
Arrows ( or ) indicate the next available line.
Rectangle ( ) indicates activity at any extension.
Steady on indicates a busy line.
Off continuously indicates an idle line.
Note: This quide covers the MDC 9000, MDW 9000, and MDW 9010. The picture shows the MDC
9000. The differences are as follows:
Instead of a Status button, the MDW 9000 and MDW 9010 have a Mute button. Press the Mute
button to turn the handset and headset microphone off for privacy while having a conversation.
The Headset jack on the MDW 9000 and MDW 9010 is located at the bottom of the handset, above and
to the left of the Handset Extension Label.
Headset On/Off Button
Press to turn the headset on and
off.