Panasonic DMR-BS750 - Manual (Page 17)

17
RQT9434
Qu
ick S
tart
Gu
ide
STEP
2
Connection
≥Before connection, turn off all equipment and read the appropriate operating instructions.
≥Refer to “Additional connections” (> 100) for connection using other terminals and connection with other equipment.
≥Refer to “Network connection” (> 103) for connection network.
≥Confirm connections not listed below with your dealer.
≥Even when your television does not have an HDMI input terminal, you still can view only with the 21-pin Scart cable connection (5) (However,
functions such as the “HDAVI Control TM ” function cannot be used.)
Using a HDMI cable
When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted. You can enjoy high quality, digital
video and audio with just one cord. When connecting to an HDMI-compatible HDTV (High Definition Television), the output can be switched to
1080p, 1080i or 720p HD video.
≥This unit incorporates HDMI
TM (V.1.3a with Deep Colour, x.v.Colour TM , High Bit Rate Audio) technology ( > 118, 119).
≥Video sources converted to 1920k1080 resolution, while of high quality, will exhibit somewhat lower subjective image resolution than true,
native 1080p full-HD sources. See dealer for details.
≥Please use High Speed HDMI Cables that have the HDMI logo (as shown on the cover).
≥When outputting 1080p signal, please use HDMI Cables 5.0 meters or less.
[Note]
≥If you are connecting to a TV that is only compatible with 2 channel audio output, audio with 3 channels or more will be down mixed (> 118) and
output as 2 channels, even if connecting with an HDMI cable. (Some discs cannot be down mixed.)
≥You cannot connect this unit to DVI devices that are incompatible with HDCP.
For units compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection that are equipped with a digital DVI input
terminal (PC monitors, etc.):
Depending on the unit, images may not display properly or at all when connecting with a DVI/HDMI switching cable. (Audio cannot be output.)
Using a 21-pin Scart cable
You can use a variety of Q Link functions by connecting the unit to a Q Link compatible television ( > 76).
You can enjoy high-quality viewing [standard definition (SD) quality] by connecting the unit to an RGB compatible television ( > 119).
≥Set “AV1 Output” in the Setup menu (> 94)
If the 21-pin Scart cable is connected with a Panasonic TV (VIERA), the following functions are available.
≥Direct TV Recording (> 76)
≥Pause Live TV programme (> 77)
Satellite cable
≥Connect both satellite terminals (LNB IN 1 and LNB IN 2) to the satellite dish when you want to record 2 programmes simultaneously or view
TV during recording.
≥Connect LNB IN 1 terminal to the satellite dish when you use only one terminal. (You cannot view if you connect only LNB IN 2 terminal.) In
this case, you cannot record 2 programmes simultaneously or view TV during recording.
≥Supply power from another device when you use 2 or more devices to receive satellite broadcast, because this unit does not supply power
when it is turned in standby.
When the unit is not to be used for a long time
To save power, unplug it from the household mains socket. This unit consumes a small amount of power, even when it is turned off
[approx. 0.3 W (“Power Save” is set to “On”)]
Regarding VIERA Link “HDAVI Control TM ” function
When connecting with a Panasonic TV (VIERA) or a receiver equipped with the “HDAVI Control” function, linked operations would be possible.
[
> 76, Linked operations with the TV (VIERA Link “HDAVI Control TM ”/Q Link)]
≥Non-HDMI-compliant cables cannot be utilised.
≥It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHS15 (1.5 m), RP-CDHS30 (3.0 m), RP-CDHS50 (5.0 m), etc.
10BASE-T/
100BASE-TX
LNB LNB
IN 1 IN 1
LNB LNB
IN 2 IN 2
OPTICAL COAXIAL
DIGITAL AUDIO OUT (PCM/BITSTREAM)
13V/18V
400mA max. AC IN
COMPONENT
VIDEO OUT OUT
AUDIO
OUT
VIDEO
L
R
Y
R P
B P
AV1
(TV)
VIDEO
RGB/S VIDEO


AV2
(EXT)
VIDEO
RGB/S VIDEO
 
1
2
COMMON INTERFACE
LNB IN AV
HDMI IN
3
6
4
5
1 2
Television’s rear panel
Satellite cable
≥Connect the satellite
cable if your television
has a built-in digital
satellite tuner. (It is not
possible to connect the
satellite cable directly to
this unit.)
To household mains socket
(AC 220 to 240 V, 50 Hz)
Fully wired 21-pin
Scart cable
( > below)
Cooling fan
AC mains lead
(included)
Connect only after
all other
connections are
complete.
HDMI cable
(
> below)
Common Interface (CI) slot
In order to view or record TV
services, refer to “STEP 1 Inserting
the CAM (Conditional Access
Module) and Smart Card” (
> 16).
Satellite dish
This unit’s rear panel
[Required^setting]
≥Set “HDMI Video Mode” and “HDMI Audio
Output” to “On” ( > 93).
(The default setting is “On”.)
Satellite cable
(
> above)
DMRBS850&750EG-RQT9434-L_eng.book 17 ページ ２０１０年１月１４日 木曜日 午後４時２１分